Well mustangers Tillman's speed shop hooked my stang up just right. All the throttle problems drivability issues have all been eliminated due to a good tune. My hat off to chris for a fantastic job. 486 rwhp.
I know where to go when it's time for 600 plus rwhp tune
__________________
2005 Mustang GT, p1sc1 procharger w/3 core inter cooler, 10 psi boost,, 39# fuel injectors, kook long tube headers, high flow cats, x pipe, magna flow mufflers, che lca, anti squat brackets, che tubular lateral stiffener bar, 1 piece aluminum drive shaft, che engine torque limiters, hurst shifter, A pillar boost and oil press gauges. Steeda lowering spring kit. CM delete plates. New eaton posi rear end(600rwhp), 3.73 gears. MAfia maf sensor, 470rwhp, 423ft# torque.
Good deal... Travelers had told me that you'd gone down there. Glad it's resolved.
Thanks this forum has been a great help.
__________________
2005 Mustang GT, p1sc1 procharger w/3 core inter cooler, 10 psi boost,, 39# fuel injectors, kook long tube headers, high flow cats, x pipe, magna flow mufflers, che lca, anti squat brackets, che tubular lateral stiffener bar, 1 piece aluminum drive shaft, che engine torque limiters, hurst shifter, A pillar boost and oil press gauges. Steeda lowering spring kit. CM delete plates. New eaton posi rear end(600rwhp), 3.73 gears. MAfia maf sensor, 470rwhp, 423ft# torque.
IT took me 7 hrs to return with tomtom. It was a two stop trip going down. Car was on dyno from noon until 6:30 pm. Lunch break in between. MAFia maf extender presented a problem with air fuel adjustments right from the beginning. Removed it and replaced maf. Things started looking better. One thing I found out that the maf sensor on my procharger is too close to the throttle body. Called procharger, now they're being installed on the intercooler. They're sending the fitting to be welded into my intercooler. I have a master welder to call to do welding, a new intercooler 1k.
__________________
2005 Mustang GT, p1sc1 procharger w/3 core inter cooler, 10 psi boost,, 39# fuel injectors, kook long tube headers, high flow cats, x pipe, magna flow mufflers, che lca, anti squat brackets, che tubular lateral stiffener bar, 1 piece aluminum drive shaft, che engine torque limiters, hurst shifter, A pillar boost and oil press gauges. Steeda lowering spring kit. CM delete plates. New eaton posi rear end(600rwhp), 3.73 gears. MAfia maf sensor, 470rwhp, 423ft# torque.
The maf is located just below throttle body in straight portion of inlet tube. you might see in this pic.
__________________
2005 Mustang GT, p1sc1 procharger w/3 core inter cooler, 10 psi boost,, 39# fuel injectors, kook long tube headers, high flow cats, x pipe, magna flow mufflers, che lca, anti squat brackets, che tubular lateral stiffener bar, 1 piece aluminum drive shaft, che engine torque limiters, hurst shifter, A pillar boost and oil press gauges. Steeda lowering spring kit. CM delete plates. New eaton posi rear end(600rwhp), 3.73 gears. MAfia maf sensor, 470rwhp, 423ft# torque.
The maf sensor being so close chris was un able to get a smooth elec. signal for idle. Mine had waves in it compared to one that was dead straight. Once I relocate my maf signal should straighten out.
__________________
2005 Mustang GT, p1sc1 procharger w/3 core inter cooler, 10 psi boost,, 39# fuel injectors, kook long tube headers, high flow cats, x pipe, magna flow mufflers, che lca, anti squat brackets, che tubular lateral stiffener bar, 1 piece aluminum drive shaft, che engine torque limiters, hurst shifter, A pillar boost and oil press gauges. Steeda lowering spring kit. CM delete plates. New eaton posi rear end(600rwhp), 3.73 gears. MAfia maf sensor, 470rwhp, 423ft# torque.
That sounds good Mike, I'm glad it fixed the issues. When you get it moved give Chris a call, he might have to send you an updated tune. It was great talking with you.
__________________
07 REDFIRE GT 5 SPEED 3.55 gears
C&L Racer CAI XCAL2/Seq signals/GTAs/Steeda UDP/CHE K Member Brace W/Torq Links/J&M LCA/Spider DS/PRO.50 Shifter Hurst handle & "T"/Meziere EO2/ARH LT catted H /Prothane MM/Delet Plates/SLP BOSS 429 Scoop/Accel COP/PowerSlot/Hawk Pads/Tokico D-Spec/CHE Panhard Bar Brace/Steeda Adj. Panhard Bar/BMR F/R Sway Bars/Cervini ducktail spoiler/BMR UCA Mount/CHE UCA/GT\CS Rear Cover/AMChrome Bullets 18x9/10s/Nitto 255/45&295/45
Tillman Dyno Tune 307HP/322TQ
That sounds good Mike, I'm glad it fixed the issues. When you get it moved give Chris a call, he might have to send you an updated tune. It was great talking with you.
Drew glad we've met hope to meet again thanks again for Tillmans info. Chris says the tune should be good once maf moved.
__________________
2005 Mustang GT, p1sc1 procharger w/3 core inter cooler, 10 psi boost,, 39# fuel injectors, kook long tube headers, high flow cats, x pipe, magna flow mufflers, che lca, anti squat brackets, che tubular lateral stiffener bar, 1 piece aluminum drive shaft, che engine torque limiters, hurst shifter, A pillar boost and oil press gauges. Steeda lowering spring kit. CM delete plates. New eaton posi rear end(600rwhp), 3.73 gears. MAfia maf sensor, 470rwhp, 423ft# torque.
The maf sensor being so close chris was un able to get a smooth elec. signal for idle. Mine had waves in it compared to one that was dead straight. Once I relocate my maf signal should straighten out.
Will it be relocated before or after the compressor?
Will it be relocated before or after the compressor?
After the compressor. The intercooler is located in front of radiator down be hind license plate
__________________
2005 Mustang GT, p1sc1 procharger w/3 core inter cooler, 10 psi boost,, 39# fuel injectors, kook long tube headers, high flow cats, x pipe, magna flow mufflers, che lca, anti squat brackets, che tubular lateral stiffener bar, 1 piece aluminum drive shaft, che engine torque limiters, hurst shifter, A pillar boost and oil press gauges. Steeda lowering spring kit. CM delete plates. New eaton posi rear end(600rwhp), 3.73 gears. MAfia maf sensor, 470rwhp, 423ft# torque.
Final tune for now 
