im looking into getting a throttle body and plenum and found one for a pretty good price but i have never here of them. the throttle body has a POWER logo on it...again has anybody heard of these and are they any good?
__________________
3.73 gears, BBK cai,BBK Throttle body and plenum, BBK long tubes with x-pipe, flowmaster 40's, steeda pully's, steeda's tri axle shifter, diablo predator, spec stage 1 clutch,spec aluminum flywheel, crossed drilled rotors front and back, ford racing springs
Yea, I put one on my buddy's car. It's a Professional Products brand, they are a little rough do to the fact that they are made in China, but for the price you can't beat them.
thanks for the info....it did bolt straight on right? you didn't have to mess with anything?
__________________
3.73 gears, BBK cai,BBK Throttle body and plenum, BBK long tubes with x-pipe, flowmaster 40's, steeda pully's, steeda's tri axle shifter, diablo predator, spec stage 1 clutch,spec aluminum flywheel, crossed drilled rotors front and back, ford racing springs
Yea it bolted right on, the only thing you might want to do is add a little LOC-TITE to the allen screw that the bracket from the butterfly rests on just so it doesn't walk on you. But besides that it's a direct bolt-on.
mine was a pain in the ass to install. the bracket that holds the throttle cable is too small so i had bore it out a little bit so my car didnt idle at 3k. if i had to do it over again i wouldve gotten the bbk or accufab. dont buy professional products anything, its all junk.
i was looking at a bbk one but it is a 78 mm which i know i don't need but if i plan on going s/c at a later time would it hurt any of my performace by getting one now by being to big?
__________________
3.73 gears, BBK cai,BBK Throttle body and plenum, BBK long tubes with x-pipe, flowmaster 40's, steeda pully's, steeda's tri axle shifter, diablo predator, spec stage 1 clutch,spec aluminum flywheel, crossed drilled rotors front and back, ford racing springs
i was looking at a bbk one but it is a 78 mm which i know i don't need but if i plan on going s/c at a later time would it hurt any of my performace by getting one now by being to big?
def go w/ the bbk...you will have no problems w/ it...plus it is a upper plenum and throttle body in one...pretty tight and a way better quality then pro products is...screw them cheap china parts.
__________________
1996 Gt 5spd.
pi conversion heads ported, comp cams, 24lbs injectors, pro-m mass air meter, bbk cold air, livewires, screamin deamon coils, bbk lowering springs, pro 5.0 shifter, mac lower and upper control arms, kyb front and rear shocks/struts, centerforce dual friction clutch, frp shorty headers, upper plenum ported, frp 70mm throttle body, frp 3:73 gears, straight pipes, 17x9 front by 17x10.5 rear cobra r's 310hp and 315foot pounds of torque!
Trickflow has the Plenum/TB combo for a decent price. Any word on them yet guys? Good or Bad? They seem like to be a decent piece.
I have seen that...i can't believe how cheap it is...trick flow is a hell of a company...i doubt to many people have it yet...i would like to see some dyno numbers on it.
__________________
1996 Gt 5spd.
pi conversion heads ported, comp cams, 24lbs injectors, pro-m mass air meter, bbk cold air, livewires, screamin deamon coils, bbk lowering springs, pro 5.0 shifter, mac lower and upper control arms, kyb front and rear shocks/struts, centerforce dual friction clutch, frp shorty headers, upper plenum ported, frp 70mm throttle body, frp 3:73 gears, straight pipes, 17x9 front by 17x10.5 rear cobra r's 310hp and 315foot pounds of torque!
I have seen that...i can't believe how cheap it is...trick flow is a hell of a company...i doubt to many people have it yet...i would like to see some dyno numbers on it.
If I was looking for a plenum/TB combo right now then I would def try the Trickflow out. It could had for around $200-$230. Not bad I say. I think MM&FF are trying them out in the next issue.
__________________
2003 Mustang GT Fobra, Sonic Blue 4R70W 262rwhp/280rwtq - Mods in profile Vortech coming soon.....
Daily Driver 2001 Mustang V6, Oxford White 4R70W
Mods in profile
If I was looking for a plenum/TB combo right now then I would def try the Trickflow out. It could had for around $200-$230. Not bad I say. I think MM&FF are trying them out in the next issue.
kewl...good to know...i'll keep a look out for that issue...i really like the black powdercoat!!
__________________
1996 Gt 5spd.
pi conversion heads ported, comp cams, 24lbs injectors, pro-m mass air meter, bbk cold air, livewires, screamin deamon coils, bbk lowering springs, pro 5.0 shifter, mac lower and upper control arms, kyb front and rear shocks/struts, centerforce dual friction clutch, frp shorty headers, upper plenum ported, frp 70mm throttle body, frp 3:73 gears, straight pipes, 17x9 front by 17x10.5 rear cobra r's 310hp and 315foot pounds of torque!
anybody heard of this company 
manufacturer 
