- 1966 289c code PCV ?
- Not charging battery...
- 1966 back-up light switch problem
- What size is my 6 cyl
- 1970 C4 Transmission Flow Direction
- 1965 Mustang 289 carb switch question
- 1966 Mustang c-code coupe More overheating questions, mostly regarding lean fuel mix.
- 1967 mustang coil spring replacement
- Leaking C-4 1968 Mustang Transmission
- 1965 C Code mustang - getting it started
- HEI Distributor?
- Brake lights/Turn signals not working. HELP!
- 1972 Ford Mustang Mach 1 Fluid Changes
- 1966 Mustang leaking oil into cylinder
- 8 inch rear end to 8.8 conversion
- cross flow head for the 200 CI 6 cylinder
- 1966 Mustang tach to coil question
- mustang and granada parts
- 1966 Mustang Driveshaft Question
- 1969 Mustang parts for restoration needed
- Do I need to change my radiator
- Anyone running Smithy "Smitty" mufflers?
- 1993ish Mustang 5.8 (351 C.I.) EFI into a 1969 Mustang
- 1969 Tansmission swap
- GT40 heads on stock 289????
- 67 289 overheating again..
- starter for a 302
- Will granada rear end fit my 68 mustang
- 1966 mustang
- 1967 Mustang daily drive
- Distributor swap
- White walls for my 1966
- 72 coupe needs new trunk floor
- Will granada parts work on a 1968 mustang
- neutral safety switch on a 1968 coupe c-4 302
- 1966 Mustang steering hoses - correct way to connect ?
- 1967 mustang fastback
- 1966 Mustang, Problems with Brake Conversion
- 1967 inline six air filter size.
- 1970 mustang pinging and knocking problem
- found severe rust in 1967 trunk (spring perches). Need help
- 1966 exterior mirrors on a 1969 Mustang Coupe?
- best way to build a 300hp 289
- 1970 mustang coupe fuel gauge problems
- Early Mech Fuel Pump Eccentric with 92 timing cover ?
- 1968 and 1966 mustang will parts from one fit the other
- 64 1/2 shifter light
- 1965 Mustang -- Mis-firing when release gas pedal
- Electic fuel pump.....Do I need a pressure regulator? '66 289
- 1968 Mustang Convertible drain question
- Windshield Wiper Replacement Units?
- Speedometer and odometer
- I didn't SEE a body shop
- 1967 mustang overhead console install?
- 1966 GT Mustang 289 Idler Brackets installation W/AC
- 1966 Factory GT Fastback
- How much to mill Edelbrock heads w/ 60cc chambers?
- 1966 Mustang 289: It's compression problems, how would this be fixed?
- 1966 6 cyl Convertible - 28 MPG on the highway!
- Freeze plug location on a '65 289
- Explorer 8.8 Axle Codes
- 289 Exhuast Help
- 66 Mustang 289 - auto trans shifts into third really late or not at all
- FoMoCo heads?
- 1970 Mustang, Printed circuit board for instrument cluster?
- need to improve gas mielage
- New Member with a 1968 Coupe 289
- 351w in a 1967 Fastback Mustang
- 73 Front grill re-assembly question
- 8.8" rear end into 1968 Mustang V8 Coupe
- 1965 Pony.Will 6cyl 3 spd tranny hook up to 289?
- 1965 mustang paint style
- My exhaust has a lot of carbon. how can I fix it?
- 1967 mustang ignition cylinder keeps falling apart
- 1966 Mustang I found