View Full Version : 5.0L Tech



  1. How bad are these motor mounts?
  2. 1995 Mustang GT 5.0HO: Cold Air Intake - no difference in performance
  3. Can I Re-use Stock Throttle Body Studs on New Cobra Intake?
  4. Which Direction should the thermostat face in a 5.0?
  5. truck flow intake hose problem need help quick
  6. Where to get hangers for 5.0 exhaust?
  7. tfs intake bolt size question?
  8. New member with 1991 Auto GT questions
  9. problems w/ ignition module
  10. 1988 Mustang 5.0 Starter Removal help
  11. 1986 Mustang GT with 5 year old fuel left in it. What should I do?
  12. Taylor "409 Pro-Race Wire"-any good for 1992 5.0?
  13. Where is the WAC realy on a 1987 mustang
  14. bbk cold air intake installation...
  15. Small Budget, Need 5.0 Performance
  16. Can anyone point me to a Fox Body brake job tech article?
  17. surging problems after Thermostat replacement
  18. sparkplugs for gt-40 heads
  19. 1988 mustang gt body work question
  20. 87 Carburated Stang, what mods next?
  21. 1992 5.0 T-5-Where does the fluid go?
  22. adjusting 1.6 roller rockers on 351W Heads?
  23. Fox Body E-Break problems
  24. 306, 331 stroker or 347 stroker.
  25. 1985 Mustang, Need Help Diagnosing Driveline Noise
  26. 1986 EFI 5.8swap
  27. 16" or 17" wheels / tires on a Fox?
  28. 1992 5.0 notchback engine rebuilt.How soon can i start "driving" it?
  29. Where is a 12v ignition source on a 1987-1993 mustang
  30. what to expect with new gears 1988 Mustang
  31. What clutch cable/adjuster to buy?
  32. Which Spark plugs to use on a 306 with 351 heads?
  33. I need help with building a 342 stroker
  34. Removing valve springs from E 7 heads
  35. 1989 Mustang Intake Question
  36. Resurecting the dead
  37. What Bellhousing Do I Have RF-F4ZR-6394-DA
  38. 87 5.0 Ignition Problems HELP!! No crank
  39. Air bag light flashes
  40. 1991 5.0 knocking after transmission swap
  41. What size throttle body would be best for my Combo?
  42. putting back 351w heads?
  43. 5.0L Fires but wont start???
  44. Need fuel injector help: 19# HO, deposit resistant
  45. Heater hoses on a 1988 5.0
  46. Tire width and Traction theory
  47. valve cover problem!!!
  48. how much vacuum should i have?
  49. Coolant Line That Connects Heads?
  50. Questions for electrical gurus about my fuel pump cut off switch
  51. How to find Top Dead Center?
  52. vacuum diagrams for 1990 5.0?
  53. Heads for a 1988 mustang GT
  54. What tire size is the best for my application?
  55. 306 with 351 Heads, What headers will I need?
  56. 81 mustang transmission identification
  57. new tremec tko stuck between gears
  58. Replacing release bearing (throwout bearing), need some help!
  59. Crown Vic spindles
  60. 1986 Mustang GT Charcoal Trim Paint
  61. 1986 Mustang GT Hood Decal Remove/Install
  62. 1990 5.0 new life then dead?
  63. Best and Worst Roller Rockers for 5.0
  64. 1987 Mustang GT, Do My Roller Rockers Need To Be Adjusted?
  65. 1991 Turn Signal Flasher Location?
  66. NEED HELP!!! Should i go with bigger injectors/mass air meter and fuel pump?
  67. 1991 up, front fender question......
  68. Motor out of balance... New toy coming??
  69. 5 lug brake question
  70. 1979 Mustang Wiring help
  71. WP rotation on 86 stang
  72. My First 5.0L Mustang
  73. What Size Throttle-body for modded 5.0?
  74. why does my f/p need to be so low
  75. Underdash wiring, plz post all knowledge and pics