View Full Version : Mustang Tech - Edelbrock water pumps- are they dependable?
- Can I swap my '91 5.0 8.8 for an '89 Ranger 8.8 rearend and does VIN say what gears?
- Who are the best manufacturers of gears?
- Whats the difference between straight through and regular mufflers?
- Want to swap my AOD tranny for a Viper T56 .. Has anyone done this swap?
- Much difference in gas mileage between running Carb or Electronic Fuel Injection?
- Max rpm limiter on A9L is 6250.. is it the same on the A9P?
- What does the term "off road" mean?
- Which weight of oil should I use?
- Have a U4PO computer.. looking for base settings to start with? Any help appreciated!
- Anyone had any good or bad experiences with certain brands of Headers?
- Data logging with GUI-EECTUNER software
- Bought an MSD.. How can I tell if it's A9L?
- K&N Air Filter vs K&N Fuel Injection Performance kit .. Which is Better?
- What is the wheel bolt pattern and offset for a 89 LX Mustang?
- OK, I just installed an MSD 6BTM...Is it working?
- Warning: High performance brake pads
- Looking for good tech on installing gears in a 8.8 rear end?
- Torque Converter.. what does it do & what performance improvement to expect?
- Looking for FAQ's on common modifications?
- Fire-breathing 427 swap for ho-hum 302
- Buying Code Reader/Scanner.. Need some Advise!
- Ignition problems? .. When accelerationg it backfires and is seriously down on power!
- Hooking up air fuel ratio gauge.. need help!
- Converting to 3.73 gears, are ring & pinion only things to change or is there more?
- Whats the difference between 302 short and long blocks?
- Has qnyone ever replaced the seal's on the Cobra front brakes?
- Flowmaster Cat-Back Installation Video Available
- Whats the Best EEC tuner Speed Brain?? What else is there?
- Which is faster 5.0 or 4.6
- What are the largest cc Combustion Chamber heads that came on a 351 windsor?
- Does swapping out springs to advance timing, work on 3.8 or 4.6 distributers?
- What basics do I need to know for a 2.3L 4 banger to 3.8L swap?
- Intake websites
- Anyone put skinny tires & on a cobra without changing factory rotors and calipers?
- Within the GUI software, how is the Engine Displacement calculated?
- How much does a Dyno cost?
- Looking for what, where and how to answers about Inner Tie Rods?
- What is the difference between mechanical and electric gauges?
- Do I need to install a clutch cable firewall adjuster or not?
- Will installing an off road H-pipe make your car smell rich?
- Drivers Seat Broken.. How can I switch it with passenger seat?
- Hesitation and sputtering sometimes after injector, intake, and plug swap
- Does it matter what transmission is behind a 5.0 EFI with EEC IV?
- Looking for fuel line conversion parts
- Need help fast .. loud humming noise coming from air tube?
- When you change gear ratio, does it affect the size of your overdrive gear?
- What is a T-Lok?
- What size gears to buy?
- Hot water leaking under drivers side. Think it might be heater coil?
- What Shifter Do You Prefer ?
- Is it worth going to an aluminum driveshaft?
- Need Pre Race Adjustments Tips and Advise?
- Anyone try the restrictor plates you can buy that replaces Thermostat?
- Can 2000 Mustang 3.8 engine be swapped out for 4.6 V8 ?
- TORNADO "As See on TV!" Does it really work? Anyone own one?
- Need More Hp! What can I get for $150 that'll give me significant hp?
- Which spark plug wires are best?
- Headers - Equal length, un-equal, short, full length, what's the difference?
- Why am I getting a vibration in reverse with clutch in?
- New to the EEC Tuner need some help & info
- Help! EEC Tuner settings not right. Anyone have info on how to tune or read them?
- front suspension noises
- Running KOEO and KOER Codes on my 89 5.0 but having a little problem
- fuel problem!@ My stang sucks up so much gas... anyone know why?
- Any idea what can cause my car to stall?
- Possible to put 5.0 342 stroker into 1996 GT without frame or body mods ?
- Is the EEC in the 93 Cobra w/24# injectors different than the 87-93 5.0 w/ 19#ers?
- code for 93 mustang gt auto
- Big Block Engines and Floorpans
- Looking for a super light good looking hood for my 02 stang. Any suggestions?
- Help! Revs go below 500 rpm engine either wants to quit or just dies!
- Ready to build my first 302 project car & need some help with engine buildup.
- Rear end hitting when letting off throttle
- Will starting car without tranny in it break anything ?
|