I would check with Jeg's or Summit first. Same thung but I think Jeg's is doing free shipping and you get it faster. 48100 - Taylor Aluminum Battery Boxes
Complies with NHRA Rule 8:1.
Required by NHRA when there is no firewall between driver's compartment and battery.
Fits most battery sizes.
Embossed Taylor logo in lid.
3 piece .040" aluminum box design allows access without removing the battery from the box.
Hard mounts battery to the frame with supplied 3/8" bolts.
Heavy duty one-piece welded battery hold down and mounting hardware included.
Dimensions: 13.5" long x 9.5" wide x 10" high.
Taylor #895-48100
Battery Box and Hold Down Components $85.99
Ships
Tomorrow
I would check with Jeg's or Summit first. Same thung but I think Jeg's is doing free shipping and you get it faster. 48100 - Taylor Aluminum Battery Boxes
Complies with NHRA Rule 8:1.
Required by NHRA when there is no firewall between driver's compartment and battery.
Fits most battery sizes.
Embossed Taylor logo in lid.
3 piece .040" aluminum box design allows access without removing the battery from the box.
Hard mounts battery to the frame with supplied 3/8" bolts.
Heavy duty one-piece welded battery hold down and mounting hardware included.
Dimensions: 13.5" long x 9.5" wide x 10" high.
Taylor #895-48100
Battery Box and Hold Down Components $85.99
Ships
Tomorrow
It does not come with the battery cable kit which is an extra 89.00. I am in no hurry since I will not be going to the track for a couple of weeks.
__________________
Airraid CAI/BAMA tune,moto blue pullies,3:73`s,LPW girdle;Powerhouse DS,CHE safety loop,CHE LCA`S & Adjustable UCA,Kooks LT`S & O/R X Pipe,prothane MM`s,Steeda CMDP`S,Eibach springs,Tokico D specs,Polished TB(by Me),Steeda radiator support,MT DR`S,Zex kit 100 shot. Taylor Relocation batter kit and cut off switch
11:933 ET, 1.674 60`,111.877 MPH 5600 feet above sea level 6900 D/A
It does not come with it. Does that make it not NHRA legal?
as long as the battery box seals and vents to the outside of the passenger compartment you won't have any problem passing tech
but you will have to have a battery cutoff switch also.....
This will explain in more detail.....
Any car with a relocated battery must be equipped with a master electrical cutoff, capable of stopping all electrical functions including ignition (must shut the engine off, as well as fuel pumps, etc.). The switch must be located on the rear of the vehicle, with the "off" position clearly marked. If the switch is of a "push / pull" type, then "push" must be the motion that shuts off the switch, and plastic or "keyed" typed switches are prohibited. Also, the battery must be completely sealed from the driver and/or driver compartment. This means a metal bulkhead must separate the trunk from the driver compartment, or the battery must be located in a sealed, metal box constructed of minimum .024 inch steel or .032 inch aluminum, or in an NHRA accepted plastic box. In cars with a conventional trunk, metal can simply be installed behind the rear seat and under the package tray to effectively seal the battery off from the driver. In a hatchback type vehicle the battery box is usually the easiest solution, since the alternative is to fabricate a bulkhead which seals to the hatch when closed.
8.1 BATTERIES
All batteries must be securely mounted and may not be relocated into the driver or passenger compartments. Rear firewall of .024-inch (.6 mm) steel or .032-inch (.8 mm) aluminum (including package tray) required when battery is re-located in trunk. In lieu of rear firewall, battery may be located in a sealed .024-inch (.6 mm) or .032-inch (.8 mm) aluminum, or FIA accepted poly box. If sealed box is used in lieu of rear firewall, box may not be used to secure battery, and must be vented outside of body. Strapping tape prohibited. A maximum of two automobile batteries, or 150 pounds (68 kg) combined maximum weight (unless otherwise specified in Class Requirements) is permitted. Metal battery hold-down straps mandatory. Hold-down bolts must be minimum 3/8-inch (9.53 mm) if battery is relocated from stock and other than stock hold-downs are used ("J" hooks prohibited or must have open end welded shut.).
8.4 MASTER CUTOFF
Mandatory when battery is relocated, or as outlined in Class Requirements. An electrical power cutoff switch (one only) must be installed on the rearmost part of each vehicle and be easily accessible from outside the car body. This cutoff switch must be connected to the positive side of the electrical system and must stop all electrical functions including magneto ignition. The external control switch for this cutoff switch will be clearly indicated by a red flash inside a white-edged blue triangle with a base of at least 12 cm (see drawing 25). The positions must be clearly indicated with the word "OFF". If switch is "push/pull" type, push must be the action for shutting off the electrical system, pull to turn it on. Any rods or cables used to activate the switch must be minimum 1/8-inch (3.2 mm) diameter. Plastic or keyed switches prohibited. Switches and/or controls must be located behind rear wheels on rear engine dragsters.
__________________
Reggie
Real Racers Don't Street Race
PERIOD.......
'88 LX Hatch With A Little Of This & A Little Of That...... 10.39 @128 MPH Soon to be faster....
as long as the battery box seals and vents to the outside of the passenger compartment you won't have any problem passing tech
but you will have to have a battery cutoff switch also.....
This will explain in more detail.....
Any car with a relocated battery must be equipped with a master electrical cutoff, capable of stopping all electrical functions including ignition (must shut the engine off, as well as fuel pumps, etc.). The switch must be located on the rear of the vehicle, with the "off" position clearly marked. If the switch is of a "push / pull" type, then "push" must be the motion that shuts off the switch, and plastic or "keyed" typed switches are prohibited. Also, the battery must be completely sealed from the driver and/or driver compartment. This means a metal bulkhead must separate the trunk from the driver compartment, or the battery must be located in a sealed, metal box constructed of minimum .024 inch steel or .032 inch aluminum, or in an NHRA accepted plastic box. In cars with a conventional trunk, metal can simply be installed behind the rear seat and under the package tray to effectively seal the battery off from the driver. In a hatchback type vehicle the battery box is usually the easiest solution, since the alternative is to fabricate a bulkhead which seals to the hatch when closed.
8.1 BATTERIES
All batteries must be securely mounted and may not be relocated into the driver or passenger compartments. Rear firewall of .024-inch (.6 mm) steel or .032-inch (.8 mm) aluminum (including package tray) required when battery is re-located in trunk. In lieu of rear firewall, battery may be located in a sealed .024-inch (.6 mm) or .032-inch (.8 mm) aluminum, or FIA accepted poly box. If sealed box is used in lieu of rear firewall, box may not be used to secure battery, and must be vented outside of body. Strapping tape prohibited. A maximum of two automobile batteries, or 150 pounds (68 kg) combined maximum weight (unless otherwise specified in Class Requirements) is permitted. Metal battery hold-down straps mandatory. Hold-down bolts must be minimum 3/8-inch (9.53 mm) if battery is relocated from stock and other than stock hold-downs are used ("J" hooks prohibited or must have open end welded shut.).
8.4 MASTER CUTOFF
Mandatory when battery is relocated, or as outlined in Class Requirements. An electrical power cutoff switch (one only) must be installed on the rearmost part of each vehicle and be easily accessible from outside the car body. This cutoff switch must be connected to the positive side of the electrical system and must stop all electrical functions including magneto ignition. The external control switch for this cutoff switch will be clearly indicated by a red flash inside a white-edged blue triangle with a base of at least 12 cm (see drawing 25). The positions must be clearly indicated with the word "OFF". If switch is "push/pull" type, push must be the action for shutting off the electrical system, pull to turn it on. Any rods or cables used to activate the switch must be minimum 1/8-inch (3.2 mm) diameter. Plastic or keyed switches prohibited. Switches and/or controls must be located behind rear wheels on rear engine dragsters.
Thank you Reggie .I was wanting to know the rules, and thought I remembered something about the cut off switch.I was going to look it up, but when I got home you had it waiting for me. Thank you very much.
__________________
Airraid CAI/BAMA tune,moto blue pullies,3:73`s,LPW girdle;Powerhouse DS,CHE safety loop,CHE LCA`S & Adjustable UCA,Kooks LT`S & O/R X Pipe,prothane MM`s,Steeda CMDP`S,Eibach springs,Tokico D specs,Polished TB(by Me),Steeda radiator support,MT DR`S,Zex kit 100 shot. Taylor Relocation batter kit and cut off switch
11:933 ET, 1.674 60`,111.877 MPH 5600 feet above sea level 6900 D/A
Thank you Reggie .I was wanting to know the rules, and thought I remembered something about the cut off switch.I was going to look it up, but when I got home you had it waiting for me. Thank you very much.
Glad to help you.....
__________________
Reggie
Real Racers Don't Street Race
PERIOD.......
'88 LX Hatch With A Little Of This & A Little Of That...... 10.39 @128 MPH Soon to be faster....
Ok I went with the Taylor relocation kit. I also found how just how hard this is to do on the 2006 mustang. I found a very interesting way of doing it. Battery relocation help - WWW.S197FORUM.COM
__________________
Airraid CAI/BAMA tune,moto blue pullies,3:73`s,LPW girdle;Powerhouse DS,CHE safety loop,CHE LCA`S & Adjustable UCA,Kooks LT`S & O/R X Pipe,prothane MM`s,Steeda CMDP`S,Eibach springs,Tokico D specs,Polished TB(by Me),Steeda radiator support,MT DR`S,Zex kit 100 shot. Taylor Relocation batter kit and cut off switch
11:933 ET, 1.674 60`,111.877 MPH 5600 feet above sea level 6900 D/A
I am still waiting for parts on this thing. Ordered the high current solenoid and had to upgrade to 1 gauge to make it the distance without draining the battery.
__________________
Airraid CAI/BAMA tune,moto blue pullies,3:73`s,LPW girdle;Powerhouse DS,CHE safety loop,CHE LCA`S & Adjustable UCA,Kooks LT`S & O/R X Pipe,prothane MM`s,Steeda CMDP`S,Eibach springs,Tokico D specs,Polished TB(by Me),Steeda radiator support,MT DR`S,Zex kit 100 shot. Taylor Relocation batter kit and cut off switch
11:933 ET, 1.674 60`,111.877 MPH 5600 feet above sea level 6900 D/A
Does this Battery relocation kit look like it is a good kit? 
I was wanting to know the rules, and thought I remembered something about the cut off switch.I was going to look it up, but when I got home you had it waiting for me. Thank you very much.
