Ford Mustang Forum - View Profile: rex1965
 
Classic Member

rex1965 rex1965 is offline

BOSS Member

  Timeslip Database

Engine type and displacement
289 cid 271hp cam
Major modifications
balanced, trw forged pistons, hv oil pump, full grooved mains
Tranny type
Manual
Tires
Street Radials
Horsepower
0.0
60 foot time
0.000
1/8 Mile ET
0.000
1/8 Mile MPH
0.00
1/4 Mile ET
0.000
1/4 Mile MPH
0.00

  About Me

  • Member Info
    Real Name
    Rex
    Occupation
    Electronic Technician
    Location
    Pittsburg
    State or Province
    Kansas
    Country
    United States
    Interests
    old mustangs
    My Dream Mustang
    1965 Mustang 2+2
    Mustang Rides
    1965 Ford Mustang Fastback, 2004 Sonic Blue 40th Anv Convertible
  • Timeslip Database
    Engine type and displacement
    289 cid 271hp cam
    Major modifications
    balanced, trw forged pistons, hv oil pump, full grooved mains
    Tranny type
    Manual
    Tires
    Street Radials
    Horsepower
    0.0
    60 foot time
    0.000
    1/8 Mile ET
    0.000
    1/8 Mile MPH
    0.00
    1/4 Mile ET
    0.000
    1/4 Mile MPH
    0.00

  Statistics

Posts
General Information
  • Last Activity: 4 Hours Ago
  • Joined: 01-19-2010
  • Referrals: 0

  Friends

Showing Friends 1 to 2 of 2

  Mentions

11-09-2015
11:02 PM - Falcondude mentioned rex1965 in post Question about running Ford 4100 with Edelbrock 2121 Intake
...heck that tommorrow rex1965 that is the exact on...
08-10-2015
09:41 PM - afisk mentioned rex1965 in post '64 260 V8 Bored to 289?
...r the information! rex1965 that site was very h...

  Quotes

12-30-2015
12:50 PM - Ivy66GT quoted rex1965 in post Self-destructing 302
I too would suspect too litt...
11-18-2015
11:16 AM - 68FastSteve quoted rex1965 in post 351W (1969 block) What to do to get 550-575 hp?
On the street a little small...
11-16-2015
02:43 PM - 68FastSteve quoted rex1965 in post 351W (1969 block) What to do to get 550-575 hp?
A rule of thumb on carbs is,...
02:29 PM - g00f quoted rex1965 in post ('65?) Trying to ID rear end
There is alot of I6 cars out...
11-15-2015
02:42 PM - 68FastSteve quoted rex1965 in post 351W (1969 block) What to do to get 550-575 hp?
I'm not sure if the 351w blo...
11-09-2015
09:15 PM - g00f quoted rex1965 in post ('65?) Trying to ID rear end
You have a bunch of raised l...
11-04-2015
06:00 PM - Cracker289 quoted rex1965 in post Refurbishing 289 Heads - are they repairable? - need help!
Okay, here's my 2 cts, again...
10-31-2015
10:25 PM - ALLYDRIVER1 quoted rex1965 in post 2004 Mustang 3.9L engine stumbles
It doesn't act like a bad pl...
10-24-2015
07:44 PM - 67 Tang quoted rex1965 in post Going to a 9" rear end
I think, on the 8" you will ...
10-20-2015
08:03 PM - g00f quoted rex1965 in post 65 v 67 Heater Box
IF my old memory serves me r...
10-14-2015
08:31 PM - ALLYDRIVER1 quoted rex1965 in post 2004 Mustang 3.9L engine stumbles
It doesn't act like a bad pl...
10-13-2015
05:23 AM - Moses7797 quoted rex1965 in post Security and insurance
Any security system especial...
10-04-2015
05:06 PM - ALLYDRIVER1 quoted rex1965 in post Questions while the trans is dropped..
i guess, i'm too old fashion...
10-02-2015
10:44 PM - RF Mustang quoted rex1965 in post Questions while the trans is dropped..
The oil is actually around 9...
10-01-2015
12:13 AM - Centershock quoted rex1965 in post re
Looks good. It is normal fo...
09-05-2015
11:15 AM - 67moneypit quoted rex1965 in post 1/2 or full groove bearings?
I personally run full groove...
09-02-2015
11:20 AM - briby37 quoted rex1965 in post Converting a 1966 to Thunderbird/Later GT350 Taillights
IF you want to do this you s...
08-20-2015
05:47 PM - btcarmd quoted rex1965 in post Autolite 4100 dead spot on transition
Please post the numbers I as...
01:02 PM - btcarmd quoted rex1965 in post Autolite 4100 dead spot on transition
Please post the numbers I as...
08-17-2015
02:11 AM - mustangman1965 quoted rex1965 in post 4 wheel disc bleeding problems
I think you have a mismatch,...
 
For the best viewing experience please update your browser to Google Chrome