AllFordMustangs.com

Powermaster 150amp Chrome Alternator

Johns01GT — Sat, 21 Jul 2007 21:04:04 -0500

by: Johns01GT

Description: Great looking piece w/ an 8-rib pulley. Only has about 50 miles on it.

Procharger D1SC, 3 Core Race Intercooler, 8 Rib Pulleys

Johns01GT — Sat, 21 Jul 2007 00:19:01 -0500

by: Johns01GT

Description: D1SC head unit, 3 core race intercooler, custom made intercooler tubing with T-bolt clamps w/ 3" 45 and 90 degree bends as well as 2 brackets. MAF on inlet side of blower. Red race bypass from Procharger. Reichard racing billet 8 rib 18-20lb pulley and billet AC delete/Manual belt tensioner. All 8 rib pulleys are included w/ Innovators West dampner. Proper length 8 rib serpetine belt. I will also enclose of the self contained oil bottles. Kit made over 700hp to the tires of my 2V engine from VT.

01 Mustang GT Stock used starter

Johns01GT — Fri, 20 Jul 2007 23:41:52 -0500

by: Johns01GT

Description: Has approximately 43K miles on it. Still works just fine. $50 obo.

2V Ported Heads, Blower Cams, Valve Covers and coil-on plugs

Johns01GT — Fri, 20 Jul 2007 23:35:30 -0500

by: Johns01GT

Description: Would like to sell everything as a package deal but I am willing to separate if necessary. Everything is from VT, heads and cams have approximately 300 easy street break-in miles on them plus dyno and a couple 1/4 mile passes. Heads flow 220/195 @ .550" lift. Cams specs are .545/236, .545/242 @.050", on 115 c/l.

P51 manifold, 75mm throttle body, fuel rails and 72lb injectors

Johns01GT — Fri, 20 Jul 2007 23:28:08 -0500

by: Johns01GT

Description: 300 street miles on P51 w/ polished Accufab 75mm throttle body, fuel rails and 72lb high impedence injectors.

Race bucket seat w/ 5 point harness

Johns01GT — Fri, 20 Jul 2007 23:23:44 -0500

by: Johns01GT

Description: Never been used light weight (less than 20lbs) Sparco race bucket seat with custom made bracket, ready to bolt in and use. New 5 point Corbeau harness. $250 obo. If you were interested in a second seat, you can find it near the bottom at this site: Seat http://www.sparcousa.com/seats_street.asp Harness http://www.corbeau.com/products/3_inch_belts/3_inch.shtml As you can see you're saving quite a bit.

VT 302 shortblock w/ electric water pump

Johns01GT — Fri, 20 Jul 2007 23:19:16 -0500

by: Johns01GT

Description: 302 Aluminum block w/ billet rods, stroker crank, CP pistons, billet oil pump gears, 7qt moroso oil pan, high volume oil pump/pickup tube, meziere electric water pump. Needs new crank and rod bearings. More pics/info available upon request.

2001 Mustang GT Rolling Chassis

Johns01GT — Fri, 20 Jul 2007 23:07:57 -0500

by: Johns01GT

Description: I'm in Maryland but the car is currently in a garage in West VA. Suspension -Front-QA1 Tubular K-member, tubular A-arms, coil-over shocks, 90/10 struts, caster/camber plates -Rear-QA1 single adjustable shocks, Mega Bite double adjustable upper control arms, Mega Bite lower control arms, Anti roll bar Safety -8 point chrome moly roll cage -Welded subframe connectors, welded torque boxes -Driveshaft safety loop Rims/Tires -Weld Prostars 3.5" front rim and 10" rear rim -ET Street 12.5" rear tire Interior -Sparco bucket seat w/ Corbeau 5 point harness -5" monster tach w/ shift light -Rear seat delete -Fuel pressure, boost and air/fuel ratio gauges -Battery relocation box in trunk w/ on/off switch Exterior -Carbon fiber Cobra R hood w/ hood pins Fuel -Return style setup -Behind Bars sumped tank -Magnafuel 1500hp pump -Weldon 2040 regulator -10 and 40 micron fuel filters Rear end -33 spline moser axles -Spool -4:10 gears -Welded 9" housing ends -LPW girdle Brakes -Strange race brakes w/ proportioning valve -13" cobra rotors and calipers That's all I can think of for now, let me know if you have any other questions.