Dyno-Tuning the 07 Shelby GT500...505 RWHP - Ford Mustang Forum
 
LinkBack Thread Tools
post #1 of 3 (permalink) Old 09-13-2006 Thread Starter
Rookie
 
Justin00Stang's Avatar
 
Joined: Nov 2005
Location: Debary, FL
Posts: 24
 
Dyno-Tuning the 07 Shelby GT500...505 RWHP

Today Jerry and myself got the opportunity to work on a gentleman's brand new GT500. With just over 1000 miles on the odometer the car still smelled like new.


All runs were done on an industry standard Dynojet 224x, you can't fudge these #s like other dynos. 93 octane pump fuel was in the tank.

We ran the car 3 times stock to get the drivetrain up to temp and get a good average HP #. The car made 421/438, then 424/427, and 419/22. I would say the blower and engine are very sensitive to heat soak.

On every run we monitored air/fuel with two widebands, boost after the blower/intercooler, and restriction before the throttle body. We also datalogged a myriad of parameters with the SCT X-Cal2 and Live Link datalogging software.

The stock tune has no timing in it at all, it's really quite disgusting. With the stock tune the air/fuel came in a little lean below 2000rpms, ran 11.5 through the mid range, and hit high 10s past 5000rpm. The car makes about 9psi of boost in stock form, just like the guage on the dash says. With the stock airbox the MAF is almost pegged, reading 4.95v.

Now that we had some good data on a stock car we started playing with the tune. When it was all said and done we arrived at 482RWHP and 477RWTQ, no you're not reading that wrong, that is approximately a 60RWHP gain. This was not a money shot either, the car was ran 11 minutes before and made 481RWHP/476RWTQ on the previous run. This was no ragged edge tune either, the Air/Fuel was 11.5:1. I was not about to blow up a brand new and very expensive car just to be an internet hero. We did not have time to let the car cool for a money shot. I was so excited that I started on the intake install right away.

I whipped up a prototype intake the night before with parts I had laying around. I took a piece of 4.5" aluminum tubing, a 4.5" cone filter, and a little CNCed aluminum flange that I had made a while back. The flange allows you to mount a slot style mass air sensor into a tube. It wasn't much, but it would give us something to play with. We had to retain the stock tube that passes between the Strut Tower Brace and valve cover. The tube is rubber with a plastic insert to keep it from collapsing, I'm sure it's restrictive, just like the stock airbox and panel filter. An aftermarket tube with thinner walls would flow a lot more air and still fit between the valve cover and STB.

The air intake required some tuning because the mass air sensor was installed in a new tube. This totally throws off the air/fuel and requires that the maf transfer function be redone, however an experienced tuner can do this in a few pulls. With the prototype intake the car made 505 RWHP/487RWTQ. Simply amazing, with the new intake the car picked up a slight amount of boost past 3500rpm, about 1psi peak at 6000rpm. The sensors were still measuring a little bit of intake restriction though, so the rubber tube between the maf housing and throttle body definitely has to go. I ordered a piece of 4.75" silicone hose, but it did not arrive until after the dyno testing was done today.

Tune with stock airbox vs tune with air intake, shown with boost.


Stock vs tuned vs tune+intake shown with air/fuel.


This car has a supercharger inlet pressure sensor between the blower inlet and throttle body, this will be handy for measuring various inlet restrictions. In the next few weeks I should have a throttle body to test.

The best part is the car feels just like stock until you romp on it. A quick 1-2 shift can now get you in trouble, even with TCS on.

We disconnected the exhaust after the X pipe, it was only worth a few HP.

I've debated whether or not to post this pic of the intake I made. Namely because its very simple and easy to duplicate. However, since I'm mainly in the tuning business I've decided it does not really matter.


A word of warning to all Shelby GT 500 owners out there. This car has a totally unique electronic control system, not seen on any other Ford (not even the Ford GT). The drive by wire system will take power away if you pulley the car, and then add it back in slowly. The car could be given what is thought to be a *safe* tune on the dyno, but then blow up a few days later.

I am still looking for several more of these cars to work on. If you are in the Central Florida area contact me.

Justin00Stang is offline  
Sponsored Links
Advertisement
 
post #2 of 3 (permalink) Old 09-13-2006
 
TrueBlue's Avatar
 
Joined: Jul 2006
Posts: 8
 
Quote:
Originally Posted by Justin00Stang
that is approximately a 60RWHP gain.
Damn - not bad. :eyepoppin

TrueBlue is offline  
post #3 of 3 (permalink) Old 09-13-2006
SHELBY GT 350 Member
 
BlueStreak03's Avatar
 
Joined: Nov 2002
Location: Trinity
Posts: 5,905
 
Send a message via AIM to BlueStreak03 Send a message via Yahoo to BlueStreak03
Wow, just wow. I really gotta get studying and qualifying my stuff at my new job so I can get my raises faster and afford one of these monsters at some point in time. That's simply amazing, 80rwhp with a tune and simple intake, nice work.

"Posterity! You will never know how much it cost the present Generation to preserve your Freedom! I hope you will make good use of it. If you do not, I shall repent in Heaven, that I ever took half the Pains to preserve it."

John Adams
BlueStreak03 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a VALID email address for yourself, otherwise you will not receive the necessary confirmation email needed to confirm, validate and activate your new AFM member account.

Failure to provide a VALID email address, will result in the cancellation of your new AFM member account registration.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
2007 Shelby Cobra GT500 Modify Daniel Bennett SVT Cobra Talk 4 02-17-2009 01:31 AM
Evolution Performance, Inc. Shelby GT500 Teaser Video! Evolution 2005-2010 Mustang GT Tech 15 08-18-2006 08:56 AM
A USED '07 Shelby GT500 on ebay mrvandermey 2005-2010 Mustang Talk 12 07-26-2006 03:24 PM
2007 shelby GT500 engine failures? fastpony89 2005-2010 Mustang Talk 3 05-21-2006 09:08 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome
 


Search Engine Friendly URLs by vBSEO 3.6.1