2012 Mustang GT Gauge Face Swap - Ford Mustang Forum
Reply
 
LinkBack Thread Tools
post #1 of 28 (permalink) Old 05-11-2014 Thread Starter
Apprentice
 
beviking's Avatar
 
Joined: Mar 2012
Location: Syracuse
Posts: 186
 
2012 Mustang GT Gauge Face Swap

Wanted to swap out the white speedo/tach on my gauge cluster. Ordered a set of GT500 style from Black Cat Customs. Was a little skeptical after reading the directions that came with the new face plate because it mentions adhesive. There is no adhesive associated with this mod! The directions included are generic. This is one EASY mod, although the speedo/tach "calibration" proved to be a pita to me and hopefully I can save you all some time.

If it isn't obvious, drop the steering wheel all the way to make room. The dash piece surrounding the gauge cluster is held in by clips and pulls straight out. I pulled the tach side to pop it loose, then the speedo, then the left air vent. Then the whole thing comes straight out. One diy I found to remove the cluster showed 4 screws, 2 at top corners, 2 below. On my 2012, there were only 2 at the top corners and the bottom was clipped in. So a 7mm socket on a ratchet extension, no ratchet, removed the screws easily. Then reach in and pull straight out from the bottom. The plug is near the top on the tach side and there was enough slack to pull the gauge out, tilt it and disconnect it. Yeah, that's it, pull the dash cover off by hand, two screws and pull the gauge cluster, disconnect the wire harness and you'll have this...

You may note that the speedo needle is not on zero. I got into this before thinking I should be cataloging it for the forums so I had already removed the cover and bumped the needle. I'll say it again later, but you should note where your needles are when the car has sat for a few minutes with no power, then put the key in and turn it so aux power comes on. Ok, you have the cluster removed, flip it over and there are 7 tabs which are easily lifted up with a fingernail enough to clear the tang. They're plastic so be gentle. There is also a T15 torx screw in the center bottom (circled) that needs to be removed, again no ratchet, just the bit, you're dealing with plastic.

With the screw removed and the clips unhooked, you can remove the cluster cover. There is a ring of clear plastic (for halo lights) on the speedo and tach that just sit over the faces. They each have two posts that fit into a hole. These lift right off. The needles pull off but you want to turn them counter clockwise as you lift. I'm not sure why but my guess is the unit is fragile enough that the force it would take to pull the needle straight up will break something so you twist and lift to get the needles off.

Now I was only interested in replacing the white gauges. A quick note to Black Cat Customs asking for just these two faces was replied to with a note that the fonts would be different and look funny (or something to that affect). Oh well. But, the faces I received where 3 separate pieces. The oem are one piece but only connected at the top...

...which I cut with scissors. It may look like the faces are connected at the middle and bottom but they are not. So I did not remove any of the central gauge needles and can't comment on them. So I'm ready to remove the speedo and tach faces. The center post that the needles came off of, have a tab that the faces have to clear seen here.

To clear it, lift the bottom of the face and slide the face toward the top. Don't worry about breaking the face, these things are thick and you could probably play frisbee with them. I didn't measure thickness but I'd say it's about 1/2 as thick as a CD or DVD disc. So here is a pic of the cluster with the piece that tied them together removed and the faces lifted.

Now it's just a matter of putting on the new faces and reassembling in reverse.
As for "calibrating" the needles; when power has been off, the needles sit below zero, then when the power is turned on (key inserted and turned to aux), the needles sweep from zero to 8 on tach and 160 on speedo, then back to zero. Once power is off for 30seconds to a minute, the needles drop back below zero. When you put the needles back on, you are pressing as you turn them on. Not sure if it matters clockwise or counter clockwise, I turned them on clockwise only because I saw someone else took them off counterclockwise. It's logical but maybe not correct? When the needles are fully on, you'll note they can be easily turned around the dial for about 75% of the travel. There is more resistance at the other 25%. So if you turn the needle clockwise until it is pointing straight down, you'll feel it has very little to no resistance going back (counterclockwise) to about zero and then it will hit a point where it catches and there is more resistance. I think its more like 80-85% but I'm simplifying for illustrative purposes. This "stop" point needs to be set at the below zero point it was when power had been off for more than a minute. When you think you have it right, set the cluster on the steering column but not pushed all the way in. Plug it in and check to see that the needles sit at zero after turning the key to aux power. I ended up (after 7 or 8 attempts!!!) setting the stop point near zero so after it swept and went back, it was above zero. I then carefully lifted the two top tabs to pry the cluster cover forward and slid a blunt piece of wire down to push the needle back. The issue is you need to set the needle back to the stop point, not the zero on the speedo. Luckily once you hit the stop point, the needle will click so you can measure how far you go back.
And here is the finished project.
Hope this helps!


'12 GT Premium, Race Red, 6spd, Roush 575SC, JLT Oil Catch Can, MGW shifter, Eibach Pro springs, FRPP Jounce kit, Steeda Adj UCA, Shaftmasters Aluminum DS, J&M Adj Panhard, UPR PH Brace, J&M LCA's, Black C stripe, 1/4 louvers, Boss spoiler w fogs, 19" staggered Chrome GT500's, MGP Caliper covers, 7 bar AM Grill, rear camera
beviking is offline  
Sponsored Links
Advertisement
 
post #2 of 28 (permalink) Old 05-11-2014
BOSS Member
 
Blazin72's Avatar
 
Joined: Sep 2010
Location: Union
Posts: 3,543
           
Garage
I did this a couple years ago. I like the font better and it gets rid of the ugly white gauge face and black letters. I bought mine from Black Cat as well but mine don't have the running horse logo. They are much easier for me to read at night without having to turn the dash lights up super bright too.

Blazin72 is offline  
post #3 of 28 (permalink) Old 05-11-2014
Apprentice
 
aggieGT's Avatar
 
Joined: Sep 2012
Location: Edinburg
Posts: 106
 
That looks flippin sweeet!!! Would you mind taking pictures of how they look at night with the mycolor on?
aggieGT is offline  
 
post #4 of 28 (permalink) Old 05-11-2014 Thread Starter
Apprentice
 
beviking's Avatar
 
Joined: Mar 2012
Location: Syracuse
Posts: 186
 
The horse was extra $.
Pic at night coming up...once it gets dark.

'12 GT Premium, Race Red, 6spd, Roush 575SC, JLT Oil Catch Can, MGW shifter, Eibach Pro springs, FRPP Jounce kit, Steeda Adj UCA, Shaftmasters Aluminum DS, J&M Adj Panhard, UPR PH Brace, J&M LCA's, Black C stripe, 1/4 louvers, Boss spoiler w fogs, 19" staggered Chrome GT500's, MGP Caliper covers, 7 bar AM Grill, rear camera
beviking is offline  
post #5 of 28 (permalink) Old 05-11-2014
Apprentice
5.0L Member
 
Wrext's Avatar
 
Joined: Dec 2011
Location: Waterdown
Posts: 212
 
This looks easier than I thought!! Great work. subscribing to see night photos!

2012 Mustang GT, Lava Red Metallic, Brembo, 401A, Cashmere leather, pedestal spoiler and hoodscoop. Mods - Boss shift knob, Weathertechs, GT fender badges, Steeda Ultra-lites/Tokico's D-specs/Steeda HD mounts & phb/GT500 iso's, 20% tint, Steeda UCA, Roush Axlebacks, Bassani X-pipe, no reso's, Painted lower valances, Boss mudflaps, MMD hood struts, MGW shifter, 275/40R19 Michelin Super Sports all around, Whiteline Sways/LCA's/Brackets, Steeda CAI, Bama 93 tune.
Wrext is offline  
post #6 of 28 (permalink) Old 05-11-2014 Thread Starter
Apprentice
 
beviking's Avatar
 
Joined: Mar 2012
Location: Syracuse
Posts: 186
 
Here's a couple color combos and standard lighting when instrument lights are off.
Attached Thumbnails
Click image for larger version

Name:	nite1.JPG
Views:	7858
Size:	94.4 KB
ID:	345186   Click image for larger version

Name:	nite2.JPG
Views:	1181
Size:	91.5 KB
ID:	345194   Click image for larger version

Name:	nite3.JPG
Views:	5315
Size:	90.5 KB
ID:	345202  

'12 GT Premium, Race Red, 6spd, Roush 575SC, JLT Oil Catch Can, MGW shifter, Eibach Pro springs, FRPP Jounce kit, Steeda Adj UCA, Shaftmasters Aluminum DS, J&M Adj Panhard, UPR PH Brace, J&M LCA's, Black C stripe, 1/4 louvers, Boss spoiler w fogs, 19" staggered Chrome GT500's, MGP Caliper covers, 7 bar AM Grill, rear camera
beviking is offline  
post #7 of 28 (permalink) Old 05-12-2014
PONY Member
 
tntoy's Avatar
 
Joined: Mar 2014
Location: Memphis
Posts: 461
 
That looks really sharp.

2014 Sterling Gray GT Premium with silver stripes / MT-82 / Brembo / Recaro
Steeda Sports | Koni Yellows | BMR Panhard and LCA Brackets
MGW shifter | Borla S-types
tntoy is offline  
post #8 of 28 (permalink) Old 05-12-2014 Thread Starter
Apprentice
 
beviking's Avatar
 
Joined: Mar 2012
Location: Syracuse
Posts: 186
 
Quote:
Originally Posted by tntoy View Post
That looks really sharp.

'12 GT Premium, Race Red, 6spd, Roush 575SC, JLT Oil Catch Can, MGW shifter, Eibach Pro springs, FRPP Jounce kit, Steeda Adj UCA, Shaftmasters Aluminum DS, J&M Adj Panhard, UPR PH Brace, J&M LCA's, Black C stripe, 1/4 louvers, Boss spoiler w fogs, 19" staggered Chrome GT500's, MGP Caliper covers, 7 bar AM Grill, rear camera
beviking is offline  
post #9 of 28 (permalink) Old 05-13-2014
Sean Reilly
Guest
 
Sean Reilly's Avatar
 
Posts: n/a
GREAT WRITEUP Bill!......I am going to "Stick" This!

Sean.
post #10 of 28 (permalink) Old 05-13-2014 Thread Starter
Apprentice
 
beviking's Avatar
 
Joined: Mar 2012
Location: Syracuse
Posts: 186
 
Quote:
Originally Posted by Sean Reilly View Post
GREAT WRITEUP Bill!......I am going to "Stick" This!

Sean.
Well thanks!!!!

'12 GT Premium, Race Red, 6spd, Roush 575SC, JLT Oil Catch Can, MGW shifter, Eibach Pro springs, FRPP Jounce kit, Steeda Adj UCA, Shaftmasters Aluminum DS, J&M Adj Panhard, UPR PH Brace, J&M LCA's, Black C stripe, 1/4 louvers, Boss spoiler w fogs, 19" staggered Chrome GT500's, MGP Caliper covers, 7 bar AM Grill, rear camera
beviking is offline  
PONY Member
 
doubleg's Avatar
 
Joined: Jan 2014
Location: Hazelwood
Posts: 339
 
Man those do look good. I might have to do his myself. That running horse sold it for me I think. LOL

Greg
2011 Race Red GT

Just an old married guy (with kids) and two expensive hobbies...
doubleg is offline  
post #12 of 28 (permalink) Old 05-16-2014 Thread Starter
Apprentice
 
beviking's Avatar
 
Joined: Mar 2012
Location: Syracuse
Posts: 186
 
Yeah it's a nice touch. I keep looking at the tach and wondering if I should have had something on that too? You can get custom lettering too!

'12 GT Premium, Race Red, 6spd, Roush 575SC, JLT Oil Catch Can, MGW shifter, Eibach Pro springs, FRPP Jounce kit, Steeda Adj UCA, Shaftmasters Aluminum DS, J&M Adj Panhard, UPR PH Brace, J&M LCA's, Black C stripe, 1/4 louvers, Boss spoiler w fogs, 19" staggered Chrome GT500's, MGP Caliper covers, 7 bar AM Grill, rear camera
beviking is offline  
Rookie
 
Mikey_Rocco's Avatar
 
Joined: Sep 2013
Location: Towson
Posts: 38
 
Great post man.

2012 Grabber Blue GT Premium - 401-A - BBK CAI - Borla Atak Catback - 3:73 Gears - Many Speeding Tickets
Mikey_Rocco is offline  
SITE ADMINISTRATOR
Mustang II Member
V6 Member
4.6L Member
5.0L Member
S197 Member
 
kenv's Avatar
 
Joined: Jan 2007
Location: Levittown
Posts: 13,198
                     
Very nice!

2013 GT CONVERTIBLE GHIG
2015 F-150 King Ranch crew cab

Dogs are not our whole lives, but they make our lives whole.
Saving one dog will not change the world, but surely for that one dog, the world will change forever.
AFM SITE ADMINISTRATOR

U.S. Navy veteran 1964-1968
kenv is offline  
Banned
 
trackpack5.0's Avatar
 
Joined: Jun 2014
Location: Fresno
Posts: 129
 
When I had my 2000 mustang when I was a kid everyone was buying the white to replace the factory black, guess no matter what color they make them someone will want to change it, looks like a lot of work, but to each his own, my 14 gt came with black gauges, the 12's came with white?


Last edited by trackpack5.0; 07-10-2014 at 08:21 AM.
trackpack5.0 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Mustang Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a VALID email address for yourself, otherwise you will not receive the necessary confirmation email needed to confirm, validate and activate your new AFM member account.

Failure to provide a VALID email address, will result in the cancellation of your new AFM member account registration.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome
 


Search Engine Friendly URLs by vBSEO 3.6.1