Search Results for ‘bearing’

Hi everyone, New to the forum but have owned and worked on modular fords for a few years. I have an 08 GT with on on3 turbo kit on the stock shortblock. In my quest for more horsepower I've decided to build a shortblock with forged pistons/rods and some other goodies to make about 500-600 WHP...

Hi all, my 2000 Mustang GT 4.6 has what sounds like a bad bearing in the serpentine belt area. I replaced the top idler pulley to the left of the alternator as well as the belt tensioner. I am still hearing the noise, it sounds like it's coming from the middle of that area. I'm thinking it's...

Hi guys im in a bit of a pretty bad situation. Recently my engine started Knocking so i took it in and they said the bearings were destroyed and oil pump shattered. I have a 2005 GT with around 100k miles. The mechanic said it be better to just buy a whole new engine rather than try to rebuild...

I pulled a rear axle to replace the wheel bearing and found a pretty deep groove where the bearing rides. I have been reading up on options. I'm going to check out the local junkyards for a used axle, but I'm not optimistic. What do you guys recommend? So far I have seen: put a sleeve on...

So it is that time where my throw out bearing is definitely shot and I am going to upgrade my clutch/TOB. I am going to a stage 2 which would be quite applicable to my car but I am concerned about stiffness. I can't stand how stiff my clutch is now and I don't want a stage 2 in there to just...

Hi, I am new here, but no stranger to turning a wrench. I mostly work on my motorcycles, but I also work on my own cars. So I have an idea what this is, but I will not sway you with my opinion. I took the video while it was 30 degrees outside. it makes the noise most frequently when i first...

I had my Cobra inspected today just as a "getting somewhat close to rainy season" thing. Turns out I need my front right wheel bearing replaced. They quoted me $125 for the "Front Hub Assembly" and then $100 for labor after tax it comes out to a little over $230. I feel like this is steep for...

So I had a major suspension overhaul about 2 months ago where I got new springs, dampers, MM CC plates, and other stuff installed. About a month later, I noticed that I had a memory steer problem and some slight clunking noise/feel near the driver side strut whenever I turned the steering wheel...

Hey guys. I'm new to this site and I need some help diagnosing a problem with my 2002 Mustang GT. There's this faint rotating clicking noise thats coming from underneath my shifter. The noise only happens when I get up to about 40mph and the sound increases as I speed up. It doesn't matter what...

I have most likely "spun a bearing" in my 147,XXX miles 1997 Cobra. I noticed oil pressure problems and grinding noises earlier this year and was heavily advised not to crank it to keep from making things worse. I took it to a shop, and they were going to charge me way too much to pull the oil...

I have a 5.0L 302 from a 91' F150. I burnt the center main bearing and I'm going to rebuild it. Looking for a forum to help with the repair. Is it essentially the same motor? And can I get help from this forum? The motor was fuel injected, got a edelbrock intake and carburetor. Was running good...

Hey guys, recently while driving the mustang around I have notice a clicking noise coming from the rear end. Almost like a card in bike spokes. You can't hear it from inside the car unless I drive by a guard rail or something that echoes it, but outside the car its easily noticeable. I took off...

Okay everyone so ive been having many problems with my car recently just my an intake on and tuned everything myself, the idle is always a little jumpy but I could not find a vacuum leak. I took it for a spin and it would have a high idle at 1500 and hang somewhat. On the test drive it had a...

I am looking for bearing spec for 1989 5.0 ho doing a rebuild. Thanks

I've got a 2011 V6 Automatic 3.73 with about 22,000 kms on it. That's about 14,000 miles. I've noticed in the past few weeks an odd kind of "whirrrr" noise when I don't have the radio up and the car is rolling. It almost sounds as it may be rolling unevenly. Like it's wobbling? Hard to describe...

ok i think the motors gone it makes a deep knock when warmed up a 900-1500 rpm range when in gear driving only!! like if im going down hill 30-50 ish put it in 4th or 5th to coast and at 1000-1500 it will go knock knock knock not in any kind of order but usually 1-3 seconds im between...

Hey my name is Chad, im in college with my 66 inline 6 project car. I noticed when i was driving i could feel a sqeaky noise coming from the front left tire i believe. and when im driving and turn the wheel it starts this popping noise. i changed all my brakes / drums because they needed to be...

I poured coolant into my new 5.0 motor for the first time the other day and found a pretty big leak, its coming from the timing chain cover, I got new gaskets and they came with a new bearing or harmonic balancer seal (not really sure what its called, but it is a rubber/metal ring that looks...

This is going to seem like a really stupid question. My girl hit a curb in my stang and i have a bent axle. Im changing it out this weekend. The axle comes with axle bearings and seals, that i can do. However the wheel bearings are what trips me up. So i have an axle and a hub bolted to the...

Hey peeps, I just put together my new short-term project "Seda" (a thread on this car will be soon to follow, but it is a 1992 hatch with a 1991 2.3L N/A engine and 5 speed) and got it running nicely but have one very annoying issue. I put in a new clutch kit (pilot bearing, PP, disc and...