brakes

My 1995 mustang 3.8 litre V6 is making a whistling (or squeaking?) noise when the pedal is pressed passed a certain point, crawled uncomfortably under the dash and had a look and there is a rubber seal over the pedal as it reaches the fire wall, it has a small hole that looks like its meant for...

I'm working on my '68 coupe that has been garaged for 15 years. When I first started messing around with the car one of the front brakes (drums) was frozen, and the master cylinder was empty. I assume the brake fluid must have evaporated, as there was no stain on the garage floor from leaking...

I have an '04 GT, and am looking to upgrade my brakes. However, all I see on aftermarket sites are the Cobra calipers for 94-04 Mustangs. Will these work on my GT regardless of them being for a Cobra, or will I need to change something for them to fit? Is there any other option to get better...

Ok, So I am in the middle of restoring a 67 Mustang coupe. I've Switched the engine to a V8 302 and replaced the rear axle I now want to change the brakes from 4 bolt Drums to 5 bolt Rotor and caliper I found this kit on ebay, I was wondering if anyone has purchased / used this kit...

I was thinking about putting on the FRPP 14" brake set. I have an 07 GT/CS with the stock 18" rims. If you look on the fordracingparts.com site it indicates rims that are compatible but those are not the 18 wheels i have. Does anyone know if the FRPP will work with the stock rims. AZChris

Could you put 1968 ford f100 disc brake spindles and disc brakes on a 1968 mustang? I have the oppourtunity to buy a 1968 ford f100 with a built 302 and c4 and power disc brakes ect. ect. Im gonna swap my engine and tranny with that engine and tranny in the truck and i was wondering if i could...

hey folks, i've got an issue...i took my ride in for routine maintenance this past weekend and the fellas at the dealer let me know that i had a brake light out. it's my driver's side rear brake. i figured that i had a bulb out on that side because my left turn signal has been flashing...

Hello fellow Mustang owners, I have a quick question for the community about the brakes on my 2006 V6 Coupe. As I come to a full stop my breaks seem to be making this creaking noise for just a moment until the rotors are fully stopped. It sounds similar to someone rubbing their palm against...

I was wondering how hard it was to change the front spindles on my 1968 mustang. Im looking to convert them from drum to disc brakes.

In my '68 coupe my brakes all of a sudden went soft. they worked fine when i drove it somewhere then when i was coming home they went really soft. I could stop the car but the pedal was as far as it could go and it was a painfully slow stop. Can anyone help me out?

ok i was looking around, i was going to buy some brake caliper paint, and while i was looking at http://www.stage3motorsports.com/product/G2BCP i relized that the v6 mustangs brakes are absolutley terrible, so i figured while i was painting the caliper why dont i just make the breaks alittle...

Ok everyone I've got a 19991 lincoln mark vii. As most of you probably know it's got the 5.0L engine, just the same as the mustangs. Now I've got an issue with the brake system, a hard pedal. The mark vii does not have a master cylinder or a brake booster is has something called a brake...

I am restoring a 1966 six banger coupe. I have a 1970 Merc XR7 351C for a donor car. I plan on swapping the entire drive train eng, trans, rear. I am also using the power brakes from the cougar. My problem so far: Upper and lower ball joints are the same but the tie rod ends are smaller on the...