Ford Mustang Forum banner


  1. Can I use S550 exhaust cams in 11-14?

    2011 - 2014 Mustang GT Tech
    Hi all, I've got a new crate engine in my 2011 Coyote. It's got the 2015 cams/Phasers/chains etc. I've been told I need to change back to 11-14 VCT for the engine to run properly. I keep getting bank 1 and 2 intake cams over retarded codes. I've heard that the S550 exhaust cams can be used...
  2. Twin Turbo Mach 1

    4.6L Tech
    Hey guys! I just ordered my Hellion twin turbo kit for my 2004 Mach 1 but I am a bit stuck on deciding what cams and heads I should use. Any suggestions would be greatly appreciated!:)
  3. CompCam's XE270AH on my 2V

    4.6L Tech
    Just here to help whoever has any questions on the cam swap with these cams on a 2V 4.6 with the Romeo block. I read just about everywhere that it would result in PTV (Piston To Valve) contact. Well it didn't. I changed my springs with Comp's recommended beehive valve springs and their...
  4. Cams or Long Tubes?

    2005-2010 Mustang GT Tech
    Hey guys I'm currently debating over long tubes or cams. I'm after an old school muscle car growl, and so far I just have the Flowmaster Outlaws. I think they sound great, but not as deep/rumble as I hoped for. However they're loud, and I'm worried they might be too loud if I got long tubes. Do...
  5. Exhaust sound fluctuates- Input

    2005-2010 Mustang GT Tech
    Hey everyone, so i want some input from you all. I have a o/r h pipe and flowmaster outlaw resonance chambers and the exhaust sound seems to flux between certain rpm ranges. On mine between 2000 and 2500 rpm seems to be the loudest and right after 2500 it quiets down. So right now i am trying to...
  6. 2003 GT Cam Recommendations?

    4.6L Tech
    Hey guys, So I have some of the basic bolt-ons done (check my profile) and I am currently getting started on suspension parts (subframe connectors, upper/lower arms, etc, all piling up in my garage as we speak) but I am always looking to upgrade power. I want to do cams next but was wondering a...
  7. what cams should i go with on a budget?

    4.6L Talk
    i am wanting aftermarket cams for my car, but its hard to save up enough and buy them, the cheapest ones ive seen are like $589, are there any cheaper good ones out there? I was thinkin stage 2 cams would be nice but starting to look like I can hang it up because I cant afford it right now...
  8. P0172 code after Cam swap

    2005-2010 Mustang GT Tech
    I have a 2009 GT. I have a CAI, Pype bombs and a Bama tune. I had some FRPP cams installed. Three days later it gave me a P0172 code System too Rich Bank 1. I cleared it and it returned again a couple days later. I changed from my 89p tune to the 87e tune and the same result. I am tanking...
  9. best cam and heads for a 331 forced induction

    5.0L Talk
    I have a DSS 331 long block. Im running a powerdyne supercharger 10 psi with a "f" cam , typhoon intake and edelbrock e street heads with better valve springs.1.6 rockers. I had to tare down the engine and im not going back together with the heads and cam. From what i hear the Ford letter cams...
  10. cam install, around shreveport LA

    4.6L Tech
    I am looking for a good shop that can install my stage 2 cams into my 2001 mustang GT. Any input would be greatly appriciated.
  11. Questions about tuning my boosted 03 gt

    I just recently bought crane stage 1 blower cams and timing gears for my 2003 GT on an 8-9 psi tune with a intercooled procharger, BBK upper intake 75mm throttle body, 42# injectors, cobra fuel rails, 3.73 gears, and was predator dyno tuned for 360rwhp and 380rwtq. But my question is what all am...
  12. Cams and long tubes on long hauls

    2011 - 2014 Mustang GT Tech
    I'm thinking about installing stage 3 comp cams and kooks long tubes with boss side pipes on my 2012 5.0. But I also drive long distance for work, would the cams cause any problems in longevity or is it ok?
  13. Getting Weird HP Numbers

    2005-2010 Mustang GT Tech
    So I just had my car dynoed for the first time since I had all my modifications done and something just isn't adding up. While doing research, I learned a stock 2010 GT puts down about 276 HP and 281 TQ to the wheels. So it was quite the surprise to me that with my modifications, I am only...
  14. Camshafts for the '06 V6? Where?

    2005-2010 Mustang Talk
    Where do you find camshafts for the 2006 4.0L V6? I can't seem to find them anywhere. All the ones I find are for the GT. Also, what are the best kind to get as far as maximum horsepower?
  15. I want a camshaft w/ Lope for my 11 GT

    2011-2014 Mustang Talk
    hey guys, my 2011 gt has bbk Lth and a bbk o/r x pipe, magnaflow cat back exhaust, steeda CAI and bama 93 tune. for my next upgrade, im looking to swap out the camshafts but im not sure what to get. i want to get that classic camshaft lope but idk what to go with. Thanks for the help in advance.
  16. Any way to get FRPP hot rod cams for less? Also, install place?

    2005-2010 Mustang GT Tech
    Hello all. I've been looking around for hot rod cams but can't seem to find any for under $730. Is there anywhere I can look to buy a set that's used? Or a set that isn't so marked up? Or do I just have to suck it up and accept it? Additionally, anyone know any places that are trustworthy for a...
  17. Hot Rod Cams With Supercharger?

    2005-2010 Mustang GT Tech
    I know there is probably 50 different threads with this and people are sick of hearing it but I could not find much in my search. I'm planning on getting a supercharger (Whipple or Saleen, don't know yet) but it wont be for awhile. I am thinking of getting the Hot Rod cams sometime in the near...
  18. New FRPP cams and cutouts installed on 2008 Bullitt

    2005-2010 Mustang GT Tech
    FRPP Hot Rod Cams W/ Stock Bullitt exhaust and CUTOUTS - YouTube This is not a cold start and idle is set at the moment to 950rpm
  19. out with the old and in with the new, need a little help.

    2005-2010 Mustang Talk
    So i have sold my 2001 Bullitt and now have a very well taken care of and low mileage 2008 GT, I have already ordered my new exhaust and i am looking into camming it soon after the exhaust install, now what i need help with is what cams to get exactly, i am looking for rough aggressive idle but...
  20. Dynamic Compression Ratio (DCR)

    2005-2010 Mustang GT Tech
    I've been studying the dark art of cam design and found some information & calculators. These only raised more questions. So I decided to start a thread (the search didn't find a previous thread) dealing with DCR and cam timing events so inquisitive people like me might have our questions...