Search Results for ‘cams’

Okay so i am looking to buy a 2011 mustang v6. I was just wondering if and or how much it would cost to put a cam in it and if i would get less mpg for doing so.. -How much would it cost to cam a 2011 mustang v6? -How many mpg would i gain or loss by camming it? -Can i cam a 2011 v6 (if so...

Hey guys, i know there are a lot of threads out there for this topic but i have several questions about this. I will be doing the PI swap and I would like to know: 1. Is there a PI kit I can buy? (Including gaskets, hoses, assembled heads, cams, intake manifold, etc. I would like to have the...

Looking for low end and mid range torque. Do I need(should I?) upgrade my brakes (i.e. brake lines, pads, rotors, etc...) when doing these upgrades to compensate for the added power? Seems like a stupid question I know, but the damned girlfriend won't let up about it and it got me to thinking...

is any one using this cam, ive been considering it, ill be running: block bored .030 over gt40 heads p/p gt40 intake p/p 70mm tb 73mm calibrated maf 24lb injectors full roller rockers msd coil & wires egr delete ... i think thats it will this cam work? any one report any drive-ability...

hey everyone So im putting my comp 270s, and all the hardware in this friday and saturday and im probably going to end up getting a new intake manifold and possible some slightly larger injectors/ fuel rail in a couple weeks I was thinking either the trick flow or the Profesional products...

Sooo I ran out of boltons.. and JUST put MAC Longtube headers on...what next... CAMS! :) I like Hitech Stage 2 Cams..what do you all think? I wanna go stage two. -How much can I expect to pay in parts (incl. the behives and all)?? -What HP gain can I see? -How much can I expect to pay to have...

Hey guys, I have a bolt on and 3.73 gears 99 GT right now. The car made 260 rwhp and 300 rwtq. I have toyed with the idea of throwing a 100 shot on the car next, and then down the road doing heads and cams and building a shortblock. But i am now thinking about doing a cam change next to wake...

i have an 89 notch, recently put canfield heads on it, tfs upper lower intake , comp cam, and some others, heres the list. can anyone tell me what kind of performance id be lookin at and if it will all work well together? and what else should i do ? 20-450-58 canfield heads tfs r-series upper...

This summer i plan on doin The PI swap and i want go ahead and upgrade the cams. How big of a pain in the but would this be? Might as well do it while the engine is apart but how hard is it to get the engine right after the new cams? A buddy of mine that is a mechanic is goin to assist me but he...

ive been thinking about getting a new cam for my car, but i dont want to have to get new valves etc., unless that wouldnt be too expensive (<$700). so i was just thinking about a slightly lumpier cam to gain a little extra power, and the throatier noise it makes. where could i get something like...

Down the road I want to put in some cams. I like to have an idea and plan of everything I'm gunna do so I had a couple of questions.. I was looking at the XE278AH Cams. Nice Rough Idle. But will they clear stock pistons (without major mods like flycutting or cam timing)? Are the XE270AH...

Hello. I recently purchased a 73 Mach1 with a 302. I need information to fill in the blanks about installing newer ( 5.0) heads on the older 302 block. Namely I have a set of 5.0 HO heads ( I can get the casting #'s tomorrow). What is needed to install these on the older block? What about the...

ive been looking into this and if its not to difficult or pricey i might end up doing it

Hey fellas, i just bought a set of factory e7te heads and am gonna try my hand at porting. I paid only 35$ so it's okay if I mess up but i'd like to have something similar to gt40 flow through them. Any suggestions or pictures for the best way to port em? I'm not interested in any valve mods...

i have an 02 gt 2v 4.6L that i bought some compcams for. the specs on the new cams are INT: EXH: {adv [email protected] .006} 267 273 (dur @ .05) 230 236...

i just bought my first 4.6 i dont know what cams are good for the car whats is a good cam that i can run that i will still have clearance i am putting on a set of pi heads and want to do the cams to and what is a good intake that will work good with the pi heads thank you oh yeah its a 96 gt...

Hey guys, I have transplanted a pretty much stock 5.0L from a 1990 Gt into my 1966 fastback. I completed the restoration last summer and was mainly concerned with just getting the car drivable. Now for this summer im looking to increase the power alittle bit. New intake, cam and heads. My...

not sure which cams to get. it's a daily driver so should i get the stage 1 from comp cams? for stage 2 i would have to get a stall converter, im not too familiar with them but im not shure i want to be cruising the streets over 2000rpm. i drive it about 40 miles a day and although gas is about...

So ive been debating on what to do to my car...and im pretty sure im going with cams and heads but i was wondering if any of you guys could give me a price... How much would it cost to get just cam's installed and how much Rwhp will they provide. and How much to have my heads port and...

So I'm wanting to do heads and cams in my car but i cant afford it right now where im in school is there any way i can safely run a mild cam with my stock heads and if so what kind of HP will i see form this.also will new intake help me out any..Thanks