Ford Mustang Forum banner

camshaft position sensor

  1. Error code P0340, 1994 V6 Mustang

    V6 Talk
    Car; 1994 3.8L V6 Mustang Convertible About two months ago, I got the car undercoated. When I went to pick up the car the Check Engine Light came on, the first time it has ever come on in 21 years! Later that night I was driving down a highway at about 60mph, and it turned off on its own. A...
  2. 2005 4.0 V6 Auto - Broken Tooth on Camshaft Reluctor Wheel/Ring

    2005-2010 V6 Mustang Tech
    Hello all, My name is Niall and I'm based in Tucson, Arizona. I recently bought a second hand, automatic 2005 V6 4.0 Litre. It has a little over 150,000 miles on the clock, but is overall in reasonably good condition. When I bought the car, it had a check engine light on. I was told by the...
  3. 2000 Mustang Ignition Shut Off - Anti-theft? Camshaft Position Sensor? Bad Wiring?

    Mustang Tech
    Thought I'd share something that's been going on for months. I found lots of troubleshooting on this board, and while some tips served as bandaids to the problem, I ended up with a tow to the auto shop this morning.... Background: Occasionally, I would go to start my car and when I turned the...
  4. 1994 3.8l manual wont fire

    V6 Tech
    hey guys, so i just swapped my engine from a 1994 to another 1994 and with everything i can think of hooked up it wont fire. i got the check engine light about a week before i did the swap and it shot the code (p0340) witch is the camshaft position sensor. i looked it up and alot of people...
  5. 06 mustang gt camshaft position sensor code.

    Introductions
    I've heard it could possibly be the alternator. I have hids, stock battery, two 12 in subs and a 1000 watt amp. It surges when cruise is on. Any thoughts?
  6. 2005 Mustang GT Check Engine Light on after Error P0340

    2005-2010 Mustang GT Tech
    OK guys, I just purchased the car about 3 weeks ago now. On Friday the check engine light came on, I stopped by AutoZone and there was an error P0340 which I found to be Cam Position Sensor malfunction. I replaced the passenger side CPS, immediately after replacing it I began having problems...
  7. 2006 mustang gt camshaft position sensor

    2005-2010 Mustang GT Tech
    I have a 2006 mustang gt.. has quite a few aftermarket parts, and since i've had it, it has had a code pop up for the camshaft position sensor. In the last few weeks I've had the alternator go bad and had it rebuilt and now that's fine. I've changed the sensor also. Then I had to change the...
  8. 2005 Mustang GT Camshaft Position Sensor Problem.

    2005-2010 Mustang GT Tech
    howdy ya'll, I have come to you guys asking if any one else has had this problem. I recently got a engine code thrown out at me, saying its my "Camshaft Position sensor System A" after putting 1300 miles on the problem (road trip) i finally got around to replacing the part. I even went as far as...
  9. 1997 3.8l Mustang Erratic Oil Pressure and P0340 OBD2 Code

    V6 Tech
    Hello all, I registered on these forums to see if anyone here can help me with a problem. I've been looking around the Internet for a number of years trying to find a solution but haven't been able to. When the engine of my 1997 3.8l Mustang is warm and in low idle (~700 RPMs) the oil pressure...
  10. 2005 Mustang GT Auto Trans - P0340 codes - Sputtering Engine

    2005-2010 Mustang GT Tech
    Gentlemen, I am new to posting to the site, but I have read through a few of the threads. I am in need of some big time help. Here is my problem. I have a 2005 4.6 GT. My car starts fine always on the first turn. I proceed to work. While approaching a stop light or anything that requires me to...
  11. 1998 3.8 Mustang Camshaft Sensor Problems

    V6 Tech
    Okay I have a Problem with my 1998 Mustang i just bought, and i was wondering if anyone else has ever had the same issues. My check engine light was on and my car slowly started to run poorly. When i idle it would sputter and run hard. Plus around 35-50 mph it would jerk when i accelerated...
  12. 1996 Mustang Camshaft Position Sensor Location

    V6 Tech
    Hey, I'm new here and I on my Base 1996 Mustang my check engine light is on. I took it to AutoZone and they checked it and said it is my Intake Air Temperature Sensor and my Camshaft Position Sensor. 20 dollars for the IAT Sensor and 35 for the Camshaft Sensor. I just need to know where they are...
Top