Search Results for ‘camshaft’

I have a 2001 v6, the engine is throwing a code(p0340) camshaft position sensor. gass milage is crappy, and it jerks at 2000 to 2500 rpms. I tried a new alternator and new sensor and that didn't work. Please help.

Does anyone know the factory camshaft specifications for a 1969 Mach 1, 351W 4V, automatic transmission, non-air, 3:25 rear end? Thanks! Mike

hey guys, my 2011 gt has bbk Lth and a bbk o/r x pipe, magnaflow cat back exhaust, steeda CAI and bama 93 tune. for my next upgrade, im looking to swap out the camshafts but im not sure what to get. i want to get that classic camshaft lope but idk what to go with. Thanks for the help in advance.

hello i recently purchased a 65 289 engine with a solid lifter cam i removed the cam and found 940358 stamped on the rear. can anyone help me determine wich cam this is ?

Hi everybody im doing an efi to carb swap on my 87 gt and am in need of help finding a good cam. Im going to be running an edelbrock rpm intake, possibly gt40 heads if i can find some for cheap, street demon 625cfm carb, and a k&n velocity stack intake. These are going in combination with the...

i hade a 2001 mustang gt was going to put camshafts in it but never got around to it then i was offered good money for my car so i sold no longer need the cams! they are brand new still in box hitech stage two camshafts will not need to replace springs its a bolt in cam! if you are interested...

Just wondering if the 1995 v6 mustang is an overhead cam or not... I got a repair manual saying it is and online they say pushrod.. :?:

so i got a new timing chain for my engine (engine has 8000 miles and timing chain went to slop?) and anywho the ford kit supplied me with a different thrust plate that has this odd little extension that covers up a small oil galley hole which the thrust plate thats on there right now does not...

I have a 2001 V6 Mustang with just under 100,000 miles on it, it does leak oil I believe out of the crankshaft seal. I Just had a new rear main seal and clutch put in. Now I'm looking for a possible cam upgrade with a nice lope and a little power gain in to it. I'm currently going to UTI and...

I just put a fresh motor together in my 93 LX 5.0 hatchback and out an E303 cam in it, i had the E303 cam in my old engine too and loved it, but i keep hearing that the E303 cam is no good and is the weak point of my motof set up, but ive also heard its a good cam for street/strip driving....i...

hi there i just bought cams for my 01 gt i am very existed to put them in who out there has also done this and what stage did you do?

OBD2 code P0340 Camshaft position sensor A - Bank 1 circuit malfunction Where is the camshaft position sensor? And can someone post a picture do there 1994-1998 v6 air intake manifold vacuumed tubes I might have misplaced them in the wrong holes Thanks

whats the best performance camshaft to put into my v6 stang? do i need to replace the rocker arms and valve springs when i put a new performance cam in or just change the cam?

Soon I plan to get a 99 or 01 mustang cobra. Over the past couple months I have been looking over modifications to give this car better performance and make it unique. One mod I have noticed is a camshaft. I kinda understand what it does, but I notice that there is a strong performance gain from...

my 2001 mustang keeps squeeling and killing the engine occasionally i've replaced the idler pully the tensioner pully and the water pump to no avail. i then ran the engine without the serpentine belt on and the problem is still present, so i dont believe it had anything to do with belt driven...

I actually have a couple questions regarding a cam I have. I put a couple of mods on my mustang about a year back such as, TrickFlow upper and lower intakes, 70mm throttle body and a trickflow hydraulic camshaft. basically my car ran like crap, under powered, stalled constantly and I had a...

hello i have a stock 1995 mustang gt that i want to put a e303 cam on. it has flowmasters and a cold air intake but that is all. do i have to make any other mods for the cam to work properly??

hello, first time posting but i have read many threads and all you guys have helped very much already. but I have some questions, i have a 289 engine in my mustang coupe and i want to increase the horsepower. Currently i have the edelbrock performer plus installed and have heard that crane or...

I am going to install these cams myself so I am trying to do a lot of reading and thinking and planning about what I am going to do to install them. I cannot find a write up anywhere on how to install them. I know they are NSR so could I just use the frpp hot rod cam Ford instructions to install...

Hey, I see that brenspeed makes a n/a cam and a supercharger cam. I really want a set of detroit rockers, but I don't know what to do. I am currently n/a but I want to eventually fo FI so is it ok to get the n/a cam and then just supercharge it when I can OR could I run the FI cam until I...