Search Results for ‘cowl’

Hello Everyone, I have become so frustrated with trying to align my hood properly.. I recently just finished painting the engine bay and re-installed the engine (with a lot of new/upgraded parts) and the last thing I need to do is reinstall this damn hood. This is the same hood/hinges I had on...

This spring was sitting in between the hood and the cowl vent. I attached an image of it. I believe it's always been there since I've had the car. I'd notice it every now and then and thought it was attached somehow and was holding something together. For some reason today I decided to check...

Im looking at cowl hood i want a very noticable cowl but not lose too much visability. Can amy one with a cowled fox give me thier opinions and height of their cowls. And also any recomendations for height i was thinking 4in. How would.that be on a street car? Its going on am 88lx when im done...

Howdy, I am a NEWBIE, so I'll probably be here a lot. My 66 Coupe projectis justgetting started, and thecar overall is pretty solid. It almost doesn't needit, but there's just enough corrosion for me to do the cowl hat repair that seems to be called "the rite of passage" for classic 'stangers...

I have a 67 mustang convertible. I had a nice restoration done some years ago but neglected the dreaded cowl until water was dripping on my leg. I live in the NY Long Island area and would really like to find a shop that is recommended by a mustang owner. I have visited body shops but when we...

I need some help from an expert , I have seen hoods for 71-73 mustangs that only have 1 cowl on the hood not the typical 2 cowl hood that most people have. I have tried to search for one myself with no luck anyone know if they are takeoffs from another car that fits the 71-73 mustang or what...

My son and I just took the passenger fender off to see the damage to the end of the cowl. We found that the end of the upper cowl (closest to the engine compartment) was rusted through. I know they make a lower cowl patch panel, but is there an upper cowl patch panel available from anyone...

So I just ordered a 95 style cowl induction hood from Cervini for my 2001 Mustang Bullitt, I was wondering what some of your guys opinions were on the hood, i am pretty sure it will look pretty good, Let me know what you think if have one or if u have personally seen one. Thanks.

Hi guys, I have a 1966 coupe with a 289 v8 and c4 transmission. The car is always kept in my garage, but the few times that I was out driving it that it happened to rain I noticed that the carpet on the passenger side floor gets wet. I know for a fact there aren't any holes in the floor...

Is there a functional pre-painted 3" cowl hood out there that won't flop and rattle around after it's installed? I've seen a handful of nice unpainted hoods on the 'net but I'm lazy and would rather pay the extra bucks for a pre-painted one. Anyone installed any aftermarket hoods? If so...

Hi im doing the body work on my 67 mustang and altho my cowl panel is very solid, there is dead leaves and flaking paint inside of it. How do I sand in there or prime and paint in there. Im changing the cars color from red to springtime yellow and I really want this to be perfect. Any advice...

Alright guys, I got the cowl section fully removed from the car. I used a spot weld remover to help me out with that. I repaired the rust problems I previously had and I went ahead and applied Por-15 coating on it, and just for kicks I through some Epoxy primer on top of that. Apparently I...

so i have been going back and forth on this one. to cowl or not to cowl,that is the question. i like the hood scoop look better, but i dont know if i want to glue/bolt something to my hood. i want it to be functionable,but dont really want to CUT a big whole in my hood. plus it has a small dint...

Does anyone have any advice for the removal and replacement of the actual dash metal? I see that you can buy new dashes online. Mine is shot. Unfortunately the evil cowl problem has destroyed the dash as well. I am going to have to replace the upper and lower cowl pieces, the dash, and the floor...

Okay, I am beat from searching for this. I am looking for a replacement cowl grille cover for my 89GT. The plastic ones are junk, and I just want something different. It could be a block off, something billet, I really don't care. Just something different from the factory one. I found a...