Search Results for ‘differential’

I wonder how strong a 7.5 trac-lok diff. is? I have heard the most they can take is 350 HP then other guys say it can handdle 400HP just fine, then some people tell me it can even take 450HP MAX!!!! wow.... but i dont know if these ratings are at the engine or if they mean RWHP??? I want to know...

Hey everyone I just got 3.73s installed and the guy who installed them was telling me that the carrier was eating away the outside of the bearing and he warned me that if we replaced the bearing and not the carrier that it would continue to eat away the bearing...now hes telling me that the...

hey everyone so i got my gears installed and the guy who put them in told me that the carrier isnt holding the bearings right so the shimms arent holding my differential tight and its causing it to move back and fourth...so i need to replace it what is a good/decent priced diff for a 2001...

can someone post a picture where their brake differential valve is mounted in their mustang II, or tell me where to mount it?

I just had a set of FRPP 4.10 gears installed last week. The mechanic told me I may hear a little noise after the install but I've also read quite a few threads about people whose gears are nice and quiet. I've been hearing three distinct noises. First is the faint "whine" I would assume is...

im trying to find where to get a brake differential valve for my 1976 mustang but i was wondering if it has to be specifically for my stang? is there a cheep universal one?

Hey everyone, I was driving the car down the highway with the convertible top up, when I thought I heard a humming noise from the rear end area of the car. Is there a real way to see/hear or test if the differential gears are going bad?

So I've decided to go with an 8.8" differential and now I'm trying to figure out what I will need to install it. any info at all would be a great help. thanks

I'm thinking of getting an SC for my 2000 manual and what I've read is that I'm going to need to redo my rear end. So before I start getting too excited about the SC I been looking into gears and differentials and I've decided that I will probably end up getting these 3.73 gears and this 7.5"...

Anyone know where I can find one? Will is this the same width as the typical 1975 Mustang II rear end? Going in to 1970 Maverick...I now you guys are all Mustang dudes...but I can hang here with you right? heh heh

I have a 67, i6 with the standard 4-lugs, I found a few disk brake conversions for this type of brakes, that way I maintain my rear differential and just upgrade. Now I've seen my rear brake upgrade to be more expensive than my front ones. Front brakes as good as 525 and rear goes for about 750...

Hi, I know that Im not very good with the mechanic ..but can anyone tell me what can I do to make the two rear wheel of my mustang turn because I have the v6 and there is only one that make burnout. So what the cheapest way to do this ? thanks for info!!

Hey there folks, I've got a couple hundred miles on my new Bullitt now, and thought it couldn't hurt to get the factory lubes and contaminants out, and get some fresh stuff in! I'm hearing a little rattling from either the trans or diff., and thought an oil change may help there. Does Ford put...

Hey guys...I've scoured the forum and internet for this question but came up empty handed. :scratchchin I wanted to see what everyone else thought this id tag deciphers to. WCZ-V1 is the casing code. From what I've found, this decodes as an 8" rear end from I believe a cougar or '67+ mustang...

I've read that they came with 2.73's, but when I jack the car up and rotate the rear tires, I'm getting somewhere around 3.3 revolutions of the driveshaft per wheel rotation. Did the 96 5 speed come with 3.27's, or 3.3 somethings, or has a previous owner done a gear swap? I've searched for...

I think I found a guy to do my gear swap, but he's pretty set in his ways and firm of opinion, and he refuses to install any foreign made gears. I know that Motive Performance gears are made in Italy, and I'm sure that many of you guys use them with success, but he says they're crap. I would...

So I'm going to replace my rear end gears, but I don't even know if I have a limited slip (posi) rear end on my 96 GT. It would seem silly to build a performance oriented car without such, but hell, they also put 2.73's or something ridiculous like that in there from the factory. It seems that...