Search Results for ‘drive’

I have an 07 V6 automatic and I'm looking for recommendations on high performance drive train parts that are rated up to 7-800+ torque/hp or if stock parts will handle the job. I don't need to know how I should do an engine swap or simply buy a new car to achieve such horsepower nor do I need...

Just wanted to share my troubleshooting journey with everyone. I finally found a major cause of my drivetrain clunk and managed to reduce it to a barely perceivable level. TL;DR at the bottom. A little bit of history: the clunk started to manifest less than 6 months after the car was driven...

Quick scenario here: 1966 Mustang Coupe. 289 4V Holley. Edelbrock intake. Pertronix Flame thrower Distributor. Just replaced the Pertonix Flame thrower Iginitor II underneath the distributor because the car was not starting for me. Now I have the car running and I thought everything was good...

The balancer on my 1998 mustang's DS has had the rubber rotted away and was just wandering around the drive shaft so i took it off my car. So now i need to replace this piece but I'm not sure how to go about doing so. Can i replace just the balancer? or do i need to replace a whole section or...

I'm new to the site and figured it would be a great place to start looking for advice on drivetrain options for my 2007 Mustang 4.0. As I understand it, Mustangs in 2007 came stock from the factory with a 28 spline 7.5in Rear-end with a set of 3.31:1's? I did some digging around and can confirm...

Alright, here goes. When I bought my car I took it to a mechanics and had it checked out, he said there were some rust on the rotors and that the chirping/squealing sound it made would go away after a few weeks. This is on my right-rear wheel. Now, two months later, it's still here, just worse...

Hey guys! We were getting ready to start dropping the engine in and were looking at all the related parts when we noticed our drive shaft had a bend in it. So we looked around and found a '68 drive shaft which we were told could be interchangeable. However, the base of the shaft is different...

Hi, I own a 2001 Ford Mustang Converible V6 3.8 L with an automatic transmission, and it has been giving me touble getting into drive. At first about 3 months ago, it had a problem going into reverse from drive. When it did this I had to put it in park and then go to reverse and this seemed to...

All, I special ordered my 2011 GT in March '10 and received it in July. I checked alot of option boxes and it came as a Sterling Grey with Machined-Face Aluminum wheels, automatic transmission, HID headlights, security package, comfort package, remote start, navigation and glass roof...

I have an 03 Mustang V6 base model and am having a slip issue that I'm not sure where it's coming from. Only during most turns, not all, I will slow down normally, make the turn, and about 75% into the turn, I will give it gas and the engine will just rev up and finally catch and lurch forward...

i have a seemingly bizarre situation with my engine. it starts great and idles just fine in park or neutral without shaking or rough spots and is fairly quiet due to a recent valve adjustment. when it is warm the car drives just fine and accelerates great and isnt lacking in power at all...

just did msd cap and rotor fr sparkplug wires 9mm spark plugs and under-drive pulleys while the hoods up and DAMN me and me dad finished around 10 took out for a quick drive not expecting much feels in excess of 20 ponies for around 130$ my old ignition must of been in bad pretty shape tho by...

Roamin' Ponies Spring Cruise 2009 Saturday, May 2nd Gather (Breakfast): 9:00-10:15am Chelsea Royal Diner, 487 Marlboro Rd (Rt 9), West Brattleboro, VT Menu & Directions on website: www.chelsearoyaldiner.com Cruise Start: 10:30am Travel: Backroads through VT into New York, stopping along...

okay so I went by a auto shop and they told me there was metal in the RWD. It sounds really bad when your driving down the road from the back of the car like somethings dry back there?!? Can anyone tell me what that means. He said it sounds like rocks in the back, I dunno what that means. 2000...