Ford Mustang Forum banner

egr

  1. 5.0L Tech
    Alright so im out of codes to fix and I have been haveing a fine idle then between the temps 110-150 I would get a really bad idle/ wanting to stall. I had thot this was the only time it would happen. I was wrong happened to me again inbetween 190-210 on the guage. I had set the tps to 96 the...
  2. Classic Tech
    So, i just put a 4bbl ford aluminum intake on my 289 block. on the intake plane there is a oval hole where the egr used to feed back into the intake (on whatever emission controlled vehicle this came from. I know i have a vacuum leak there and it is causing fluxuations in rpm. is there a way to...
  3. 5.0L Tech
    Got a 87 gt stroked 5.0 bored 30 over, gt40 heads, svo roller rockers,gt40 lower,gt40 tubular upper,cammed and wondering can i run stock egr PLATE temporarily with 70 mm tb?:?:
  4. 5.0L Talk
    where can i get these from other than the junkyard, 5.0 are striped to the bone everytime find one anyway, i have some power loss and i know i have a few broke lines, but it could also be my gaskets or rings
  5. 5.0L Tech
    Strong fuel smells make me fairly uncomfortable so i really want to figure this one out sooner than later. Only when she's idling but not all the time, it goes in and out day by day. The vaporizer canister has been replaced already. Took care of a check engine light due to codes from the EGR...
  6. V6 Tech
    Hey, I have a 00' 3.8l Manual that has a cut in the exhaust just after the cat on the passenger side. I swapped my engine back in march and it has run great since then, All I had was a code for insufficient EGR Flow. But all of the sudden when I take off it starts going really rough and groggy...
  7. 5.0L Tech
    Building a 408w, Edelbrock victor Jr heads and victor 5.0 intake. I is not meant for the egr setup(non EGR). How do I delete the rest of the components from my stock 92?!? I was goin to buy a new top end setup for egr to keep it stock but do I need different heads then too??? I heard that I...
  8. 2.3L Tech
    my turbo coupe wont rev past 3500 while driving, i ran the codes and it flashes out 34 which is insufficient egr flow, could that be the reason i cant go past 3500 while driving, when im idling it will rev where ever i want, ive replace the cap and rotor, fuel pump, fuel filter, plugs and wires...
  9. Classic Tech
    Hi guys, I have a 1966 coupe with a 289 v8 and C4. Right now, I have a stock intake manifold with a stock 2bbl carb. The stock 1" spacer has a port on the back that has a hose running to the right valve cover. If I'm correct, this is the EGR valve? What I wanna do is replace the stock...
  10. V6 Tech
    hey guys, i just took my car to the shop to get my headers gasket changed cuz i thought i blew it. turns out i have a crack on the header itself, now the mechanic took it of and the egr pipe also. but due to the egr tube being so old it stripped the splines. im thinking about just welding the...
  11. 5.0L Tech
    Hello, I'm a new member here... Just bought my 1990 white LX 5.0 Hatch 5 spd with only 60k original miles 2 weeks ago. It's in great shape. Interior is near perfect and paint is great. It has a rough idle, not bad, just a little rough. I gave a full tune up including cap and rotor, plugs and...
  12. 2.3L Talk
    So i ran a code tester for my car & from the codes i received i need a TPS & EGR. where can i get these parts from the cheapest.
  13. V6 Tech
    After spending the last 7 hours working on my pony to try and replace my rusted exhaust manifold, I finally got it done! (Phew!) Now... the biggest trouble I had was trying to remove the EGR bolt that was on my original header. I ended up having to take a torch to it to loosen it up and by the...
  14. 2.3L Tech
    I have a 1991 Mustang LX 2.3l N/A. and my EGR valve failed, i cant find one in the junkyards around here and i cant afford a new one from my local parts stores, so i was wondering the easiest and most cost effective way to just block it off. What kind of tools, materials, and if i need any screw...
  15. 2005-2010 V6 Mustang Tech
    My 2005 v6 mustang is throwing codes ( P0401) about getting insufficient flow though the EGR (exhaust gas recirculation). Last week i had taken the pipe off and exhaust manifold to see about fitment for longtube headers. Later i put it all back on, now i get the check engine light. After...
  16. 5.0L Tech
    i am getting a misfire at about 3000rpm i have replaced the dist,cap/rotor, coil. fuel pump, tps, plugs and wire have heard that it may be the Egr the self test codes are showing 34 for egr issue....any ideas or input?
  17. 2.3L Tech
    Okay so I keep reading about the EGR getting unplugged helps out. Some people are saying just unplug it, others say block it off. Whats the best way to do this and why? I was thinking about just going and unplugging it, any problems with that? Thanks guys, Apollo P.S. - I'm no...
  18. 5.0L Tech
    I have an 88 gt hatch with a 93 5.0 motor in it. It just passed pa inspection so I want to take off the smog pump. what all is envolved with taking it off other than just removing the pump from the engine and belts? does anyone have pictures of a smogless fox or know of any good threads? thanks!
  19. 2005-2010 V6 Mustang Tech
    I am having EGR Problems, have a , 2005 Mustang Hi, My car's check engine light will not go off. The code is P0401 which says "Exhuast Gas Recirculation Flow insuff detected" I have a superchips tuner and turned the light off but it always comes back on within 40-50 miles. The Real problem I...
  20. 2.3L Tech
    I did the egr delete and covered the hole with a plate good and tight. I even waited till the next morning to start it up. Sprayed it with carb cleaner and no leaks. But when it gets warm after like 3 to 5 minutes later it runs erratic and automatically shuts off. If you can help it would be...
Top