Ford Mustang Forum banner

exhaust manifold

  1. How to disconnect exhaust manifold to pull head

    SVT Cobra Tech
    Hi guys. I have a bunch of stuff removed from my ‘96 Cobra to pull the driver’s-side head. What needs to be done to disconnect the exhaust manifold? The factory manual procedure is outrageous. Thanks for any insight. Gavin
  2. 351w in 1965 Header Recommendations

    Classic Tech
    Hey all, I am beginning to consider getting headers as my next upgrade. The car already has full dual Flowmaster exhaust but I'm running an exhaust manifold. So I'm asking you guys which headers you would recommend to me that will fit well with the 351w inside of a 65. Thanks again guys, Adam
  3. strange port on exhaust manifold? What is it?

    Classic Tech
    Hey all, I'm in the process of a rebuild and I've always noticed this strange port on my exhaust manifold, but never known what it is. It has always leaked a little bit of exhaust. Is it just a manifold temperature sensor that someone once had installed or does it have some other purpose? I'm...
  4. Tool for tightening EGR tube nut to exhaust manifold

    V6 Talk
    I've re-registered (very annoying process) on this site to provide a bit of useful information since the only thing that came up when I googled was Robogrips. For tightening or loosening the EGR tube compression nut on the passenger side exhaust manifold for a 2002 v6 Ford Mustang (I'm sure it...
  5. Intake Mainfold for 2010 V6 Mustang?

    2005-2010 V6 Mustang Tech
    I have been searching for a new intake/exhaust manifold for my Stang for awhile. Have not been able to find one. Should a replace the throttle body first? Already have dual exhaust and cold air intake. Plan to buy a tuner soon as well
  6. 1999 v6 smoke coming from engine/dipstick, Please Help!

    V6 Talk
    Okay, so when i drive in the city everything's fine but when im on the highway and i take it passed 65 mph for like 45 seconds or more, the engine starts to smoke, you really don't notice it until you've come to a stop and you see the smoke coming from the wheel arches. But last night i stopped...
  7. Heat riser for a 6 cylinder

    Classic Talk
    I'm putting on a new carb and exhaust manifold - both brand new. Apparently they do not sell heat risers at any of the Mustang places like NPD. Does anyone have one or know where to get one? Thanks!
  8. Interested in long tube headers

    V6 Talk
    Hello, I own a 2004 3.8 v6 mustang and I recently had an exhaust installed. I have Pype's catted X- pipe for v6 and SLP loudmouth catback. My question is I wanted to get pacesetter long tube headers and I didn't know if they would fit. I'm trying to get a throatier sound and wondered if shorty...
  9. Carburetor for an inline 6 & Exhaust Manifold

    Classic Tech
    Hi. I'm looking for an original carb for my 1966 inline 6 cylinder, 200 engine. Or if someone knows a good quality new carb. Also, I need an exhaust manifold. Any ideas or suggestions appreciated. Thanks.
  10. White smoke/steam coming from rear of engine of 67 Mustang 289 -- blown head gasket?

    Classic Tech
    Hey there everyone, I have a 67 Mustang Coupe with a 289 engine (V8). I bought it about a year ago with only a few minor problems. Since then, I have replaced the gas tank, several cosmetic aspects, and have just recently had to move on to work on the engine. I had to install a new thermostat...
  11. 2001 bullitt head swap please help

    4.6L Tech
    ok I have a 2001 bullitt with the stock motor in it. I purchased patriot stage two heads and a set of comp cams and all the little goodies that go along with a head swap. i have removed the intake the timing cover and i have both heads loose but i cannont seem to get to the exhaust manifold...
  12. 2005 Mustang GT-quick exhaust manifold question....

    2005-2010 Mustang Talk
    The stock exhaust manifolds on the 05+ GT are same as short tube headers in their size?, meaning no need to replace the stock h-pipe if I want to put a set of better flowing heads/manifolds on the car?
Top