Ford Mustang Forum banner

fit

  1. Body shop fails to properly fit replacement rear bumper(s)

    2011-2014 Mustang Talk
    External circumstances unfortunately wrecked the left side of the rear bumper and bent the left side quarter panel on my Mustang.. So far the body shop have straightened out the quarter panel and (because of insurance requirements) got an aftermarket rear bumper that they fitted and then...
  2. 1972 Mach 1 Mustang Engine Swap to a 2003 Supercharged Cobra Mustang Engine ADVICE?

    Classic Tech
    Id just like to first thank you for taking the time to helping me out. I have a 1972 Mach 1 Mustang Fastback has a 351c with 2v heads and a 4 barrel edelbrock carb currently. And Automatic Transmission I might be able to get my hands on a 2003 mustang Cobra supercharged engine for free has 500+...
  3. s197 rear wheel and tire q's

    2005-2010 Mustang GT Tech
    im looking for new wheels and tires to increase traction. Ive looked around google and this site, and yet i still have no definite answer to my question; what rear wheels and tires can i run on my mustang without rub issues! Last weekend i took my mustang to big bear to do some snowboarding...
  4. 2010 hood scoop fit my '05?

    2005-2010 Mustang Talk
    hey i was just wondering if the 2010+ hood scoop would fit my 2005 gt? i mean it seems like it would but i was wondering if anyone has done it or seen it? pics would be greatly appreciated
  5. 2000 Mustang wheels, what will fit?

    V6 Talk
    I have been looking around on Craigslist etc... to find some nice looking rims for my 2000 Mustang, but I don't want to buy any and then find out they don't fit. What should I look for either on the rims or in the posts to be sure they will fit my pony? -Thanks 2000 3.8 V6 auto -I will be...
  6. A COMPREHENSIVE "what size wheel/tire fits?" list.

    2011-2014 Mustang Talk
    hi i just bought a 2011 v6 premium recently, moving from a mr2 spyder to a mustang to a huge difference, also the forum is relatively new in this section too. from my other forum there's a wheel fitting guide and info, so might as well start 1 here. or not. A COMPREHENSIVE "what size wheel/tire...
  7. would this transmission work in my car?

    Classic Tech
    I have a Ford 4 speed toploader type transmission with a 14 inch tail shaft I have no current need for. Wide ratio gearing. 10 spline input shaft, 28 spline output shaft. I do not have a bell housing or the linkage. The gears look as good as new. Perfect original piece for a hot rod, muscle car...
  8. Aftermarket Plenum fitment with Strut tower brace

    4.6L Tech
    What's up 4.6 guys... I did a search first, and didn't come up with anything relevant. :bigthumbsup I want to put a C&L Plenum on my car. I'm hesitant though because I read that the Professional Products plenum could cause fitment problems with the discharge tube on my supercharger and my...
  9. Restoring a 66 Mustang. Question about tire size

    Classic Talk
    I am in the early stages of restoring a 1966 mustang coupe with a 289 . I will be performing the shelby drop or upper control arm relocation. How big a front tire can I put on a 15x6 1/2" rim in the front after the drop without clearance issues. i was planning on a 215/65R15 .Thanks for the input.
  10. will these rims fit my 07

    2005-2010 Mustang GT Tech
    im looking at Stage 3 Motorsports 18x9 & 18x10 Chrome Roush Mustang Wheels (Set of 4) - Clearance they look really good but im wondering if they will fit a 07 v6 premium mustang, or if they will stick out really far, and if they will fit but stick out far, should i go with 18x9 and 18x9...
  11. 1970 mustang seats in a 1968 Mustang coupe

    Classic Tech
    I was wondering if anyone knew if i could put 1970 mustang seats into my 1968 coupe. I know that i will have celing clearence but i am unsure if the bolt holes in the floor are the same distance apart from eachother. Can someone tell me if they will work, or give me some measurments so i can...
Top