Ford Mustang Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-14 of 14 Results
  1. Classic Talk
    Anyone have a good source and/or supplier that might have secondary air injection system components? I have part numbers (all part numbers that are highlighted) but can't seem to find them anywhere else. Any help would be greatly appreciated.
  2. 2015-2023 5.0 (V8) GT Tech
    I know 3 of them are resonator, PCV and brake actuator. What is the small one beside the PCV hose? It runs up under the manifold. The clip on the disconnect broke on mine and Ford is saying I need to replace the entire hose which will require me to remove the manifold and cost me over $600...
  3. 5.0L Tech
    We need help finding a part number or getting any ideas to replace this vac hose line. Provided are pictures to specify exact part we need replaced. Thankyou !!!! Pic 1 is diagram circled in red. Pic 2 is the tree / A/C is the one we need to replace. Pic 3 is the other end ( EVAP Gasket) Pic 4...
  4. Classic Tech
    Hey guys I was installing a disc brake conversion on my front end and I was trying to disconnect the hard line that is attached to the rubber line. Does anyone know where I can find this line? Its actually coupled together in the engine bay and goes through the fender and connects to the rubber...
  5. V6 Tech
    ok i have a new problem here again. as it turns out there are no hoses connecting to me heater core. all i need to know is were do i connect the hoses to? im getting new ones soon but i need to know where they go
  6. 5.0L Tech
    im swapping my stock intake manifolds (upper and lower) with gt40 upper and lower and i noticed the stock lower has some hoses that dont seem to have a place on the gt40 lower. i know lots of you guys have done this swap so i was wondering what you guys did with this? im guessing you just...
  7. 5.0L Tech
    i took apart the top of the intake manifold to replace the gasket. now i have a problem i cant seem to remember where some of the hoses go... so if someone could send me the diagram you would be a life saver!! thanks
  8. 5.0L Tech
    Ive been looking up deleteing my egr. Seen alot of posts about this. So Can I just make a back plate drill some holes in it make a gasket out of rtv and cap it? I would also block off any vaccum hoses etc. I was looking at other forums and they say that when my car notices the egr is...
  9. 2.3L Tech
    Hey there, I have a question or 2 for those who may be able to help me... My Pony has just recently been acting a little strange. It seemed as though Fuel wasn't reaching the engine as it should, so there were some possible options that came to mind. The Electric Fuel Pump could be bad, or a...
  10. Classic Tech
    I have a stock 289 in my 1968 fastback. I want to change out all the hoses and lines under the hood. Is there any one who makes a kit for this or can you tell me where I can find these hoses?
  11. Classic Tech
    Quick question. I am replacing the vacuum advance line from the vacuum advance unit on my Load o Matic Distributor to my carburetor. I figured it'd be a simple installation, but the new steel vacuum line that I received has fittings on the ends that just slide off. The ends of the vacuum...
  12. 4.6L Tech
    Hello all, new to the forum and hoping to learn a alot from you all. I've just recently purchased my first Mustang, a 2001 4.6L with 56K miles for $4,000. I know i stole the dang thing, couldnt pass it up. Car runs great, only thing i had to immediately replace was the #3 ignition coil which was...
  13. SVT Cobra Tech
    Where the heck can I find a new performance hose set for my 1995 Cobra?:?: Preferably in blue! IT'S VERY DIFFICULT to find parts for the '94-'95 Cobra's! Any and all help is appreciated. Thanks
  14. 5.0L Tech
    anybody know if the ford racing radiator hose kit comes with the two hoses that connect to the heater core? i look at pictures but cant tell if there for the heat or the a/c. i want to buy a kit but need to know this first. thanks.
1-14 of 14 Results