install

Update: Sooooo, I went ahead and did it :-) I like the look, rice and all ;-) Pictures at the end. A bit blurry and distorted due to low light. I got just the right amount of light. Hey guys, I am looking to put in some wheel well lights (not tire or rim lights). I was thinking about...

I'm having a little trouble figuring out what fittings I need to install: AEROMOTIVE Part # 14101 86-98 Ford 5.0 Liter I currently have a stock fuel set up, with aBBK 86-93 Ford 5.0L Adjustable Fuel Pressure Regulator. Basically I'm trying to figure out what fittings I need. Here's what I...

Has anyone ever cut out the small fog light plastics in the bumper and put actual fog lights in a base model? Cant find anything that has been done. If so, is there a wiring harness that is hidden or will i have to buy one? Thanks!

Hey everyone, i just got some black Lemans vinyl stripes. I have delt with applying grpahics before on a dirtbike and i know uneven curves can cause the worst trouble and sometimes even ruin your graphic. I have an after market hood and there is a hood scoop in the middle and a leading edge...

So I just replaced the clutch and I am trying to install the tranmission and am having a lot of issues. Currently the engine is still installed and the tranny was pulled out from underneath. I can get it close but I am off by an inch and it seems like there are two ...'nubs'...that press against...

I am interested in getting a complete suspension kit install on my 2011 GT and wanted to see if anyone had a recommendation on good install shops. I am on the south side of town and PSI Motorsports is the closest speed shop to me. Any info or leads would be helpful.

Has anyone installed a digital stepper motor pyrometer gauge from autometer? Its a phantom 2 series, and its on a 2006 gt. So here are my couple questions. 1. It needs a direct engine ground, so where should i mount it on the engine 2. If the ground wire is too short, can i splice more wire...

I bought a fuel tank kit from mustangs unlimited. Should I paint the bottom of the gas tank before I put it in, in order to prevent rust. Also what sealant should I use to put the gas tank in?

There aren't many auto performance shops around where I live, so the two shops I came across that are capable of the labor are both asking around $3,200 for the install of a set of cams on my 02. That number doesn't include the tune, either. Now, I've never installed cams on a motor, but this...

I want to get one of those sunpro triple gauge packs. However since my car already has a water temp gauge I want to use it as a transmission temp gauge. Is it possible to do this. How do I install a temp gauge for my transmission on my 1965 mustang since it didn't come with one

First off.. I'm pretty embarrassed for having to make my first impression this way... I'm a long time ''learner''on this forum and unfortunately put myself in a position tonight where i need to break my silence and ask for help.. Any and all feedback is appreciated, even a little bashing is...

I'm still taking my 1966 coupe apart. Got the glass out and I see that the headliner is installed under the front and rear glass seal. My headliner is in good shape and I need to remove it for some repairs. If I need to install it under the seal I'll prob go with new then, just so I wont need to...

Hey all, After countless hours on AFM (and many other sites) comparing exhaust notes, prices, looks, and driving my wife crazy, I decided to go with the Borla S-Types. I'll get to the review in a sec, but my advice for anyone out there jumping back and forth between Borla, Roush, FRPP...

Ok so I’m thinking I need to just stop touching this car cuz once I fix one thing it breaks another thing! lol On this week’s journey I decided to finally fix my radio! I figured it didn’t work cuz the speakers were bad/old so I replaced them still not working so I pulled the radio and...

I just installed Flowmaster Force II dual exhaust which bolts in to the factory Y pipe. Here are a few issues I ran into 1) The holes in the flange which bolts into the factory Y pipe would not align, so i had to actually grind it quite a bit to finally get it aligned 2) The flange does not...

The clamps connecting the muffler to the Y pipe are rusted badly and the muffler is not in great condition either. So I am thinking of replacing it with a catback system like the Flowmaster Force II or something similar. How easy would be to install it myself ?If anyone has done a similar...

Hey all, I bought a Flowmaster Outlaw series axle-back for my 2010 GT a bit ago. I finally got around to installing it, but I'm having a HELL of a time taking off the 3rd bolt on the 2nd hanger from the driver's side muffler. I can't seem to get to it with a normal ratchet or anything. It's...

IF I was to come across on of these for cheap, what has to happen for it to fit onto my 4.6 in my 2008 GT ? I am not sure on the Fitment for these, any information would be helpful thanks a lot everyone :)

Hi all, First off, I'd just like to say as a new member, what a great community AFM has got! I've already learned a ton and started to chime in on some threads as well. I'm awaiting the delivery of my first mustang and I was hoping some of you veterans may share an experience or two with a...

Hey guys, I was wondering if you could give me a rundown on the differences between a Turbo and Supercharger? I know some basics, like Turbos seem to be more expensive and one runs off of air while the other is belt driven, but that is about it. What are the advantages, and disadvantages of...