Ford Mustang Forum banner
Cancel

Search Results for ‘install’

Discussions Showcase Albums Media Media Comments Tags Marketplace

181-189 of 189 Results

Search Tags

1965 1966 1967 1968 2.3 2005 2006 2007 2011 289 3.8 302 4.6 5.0 alternator american iron cmc mustang automatic battery brakes bullitt cai cam cj pony parts classic clutch cobra cold air intake conversion convertible coupe electrical engine engine swap exhaust flowmaster ford ford gt fox body foxbody fuel fuel pump gears gt500 headers headlights heads hood horsepower idle ignition install intake interior introduction leak lights mach 1 manual misfire mods muffler mustang mustang car show mustang gt noise oil paint parts performance power problem problems radio rear end rebuild rims roush s197 sale sct shelby sn95 springs starter steeda supercharger suspension swap throttle body timing tires transmission tune tuner turbo v6 mustang video videos wheels wiring
  1. Classic Tech
    Hi, I am installing an aftermarket transmission kick down cable, similiar to the one made by lokar, and am not sure how to set up the tension initially? I have the lokar braket on my carb and one end of the cable already attatched to the transmission. I am just trying to finish the other end on...
    cable install kick transmission
  2. 2005-2010 Mustang GT Tech
    Im trying to install an autometer boost gauge on my 05 mustang w/roush s/c. which vacuum line do I use for the gauge. The directions from autometer dont help much. Thanks in advance
    boost gauge install vacuum
  3. V6 Tech
    Hi, I see at autohow.tv that when you install the new crankshaft pulley that you need to torque wrench it at the good lb.-ft torque. But in this video : How To Install Underdrive Pulleys | AutoHow.TV this installation is for the gt but what is the good lb.-ft torque for my mustang v6 2001...
    crankshaft install mustang pulley torque
  4. 2005-2010 V6 Mustang Tech
    Ok Guys, I got a footwell lighting kit that I'm trying to install, but I've ran into a wall!!! What power wire do you splice into to hook up the kit? As in, I'm trying to hook mine up, so when my dome map lights come on, the footwell lights do too! That's the power wire I'm looking to splice...
    dome light power wire footwell install lights
  5. V6 Tech
    I'm looking to reduce the amount of turning the steering wheel to actual wheels turning... What should I search for and any comments on whether I should do it or not, because I'm indecisive about doing it...? Any idea or guesses on how much it would cost to get it done?
    install reducer reducing steering wheel
  6. V6 Tech
    on my driver side fender there is some damage and I am needing to replace the fender and the inner fender AKA splash shield I was wondering how you go about taking it off and putting the splash shield back on.:gringreen PLEASEE HELLPPP MEEEEE !!!! :wavey THANK YOU SO MUCHHH!!:happyhapp
    exterior fender install panel splash shield
  7. V6 Tech
    hi, recently I withdraw the intake manifold of my mustang and now I want t install it again but I just want to know if we can tighten the screw ike we want or there is a specific tightening torque! And if it as one what is it and am I obligated to torque them specificaly? Please help me thanks!
    install intake manifold mustang screw
  8. 2005-2010 Mustang Talk
    If anyone can expalin how to wire up the fog lights and piaa lights in detail i would really apreciate it. :hihi:
    c-series fof light install lights piaa
  9. 4.6L Tech
    what does it take to install the kenne bell s/c....what do i need to change in my motor or will it bolt straight up to a factory minor bolt on gt....how does it affect the dependability of a gt and how does it affect the life of the car...thanks guy and gals
    install kenne bell s/c supercharger
181-189 of 189 Results
Top