Search Results for ‘motor’

Hi guys, I need to take my motor apart and need a overhaul manual for a Ford 302 that is in my 66 Mustang. Acutally it's a stroked 347 but I guess there is no big difference in the single steps. I would need the manual as a downloadable PDF for instance, no book recommendations please. Thanks...

I love my little '67 289 but every time I look under the hood, it looks like every other motor off an old driver. So I was thinking about repainting it. Since I have it out, I should probobly rebuild it too! I have done a lot to fix it up already but my questions: 1. What should I replace in the...

Hey i was serching the site and i couldnt find anything just wondering if anyone did or has information on a 4.0 to 5.0 swap in a mustang. I'v seen it done on 1 other site but i couldnt get to much information on it other then its possable to do with a change of engine mounds battery relocation...

I have a 2001 Cobra that has a knocking sound which seems to be coming from the bell housing/back of motor after a few minutes of the car warming up. The knocking gets faster with increased RPM. I thought it might be from the clutch and took the transmission out. I replaced the throw out...

ok i was reading and they dont make a rebuild kit for the 2.3l turbo motors??????? well i am pretty sure you all read my post well i think it is the rings well that is what every on is telling me so i must do some more research. my dad is a great car builder so i am prepared, my dad has built...

hello, i took a 93 ford f150 302 motor, fuel injected and have put it in the 68 mustang. i found out the hard way the transmission wouldnt fit, i have got a c6 that i believe to be is a 80's model, not real sure though. my question is what would be the best transmission to put in the car and...

I recently tried to use my blower and relized I have lost speeds 1 through 3, but 4 works. Doing research I heard it could be the resister. Anyone have any ideas and is it an easy fix? It just happened. Thanks for any help!

Hey guys, about one and a half years ago I've bought a 66 coupe that a guy started as a project car but never finished it. It came with a brand new custom built 347 stroker. This summer the car got finished and is running very nicely. Now here's the problem: The motor builder has put a 750 cfm...

I bought this 05 triple black convertible with a bad motor. Im replacing the V6 with a lesser mileage v6. I am just about to remove the motor and I noticed the trans is leaking a bit. Has anyone ever pulled out both motor and trans together in one piece, If so, how did it go and is there any...

I was wondering a few things that a true Mustang lover would know. On a 2001 Mustang GT Convertible, do the power seats move when the car is powered off, and key is not in the ignition? Just noticed when I went to move the seat in my Mustang I am looking to buy, it doesnt move. The car was...

so my dad and uncle own this dirt track car. i think he said it was a 427 block with a 350 crank and rods but pistons to match the block. so basically i've seen some 3.8's turned into 4.3's. what turns that 3.8 to the 4.3? does it keep the same block and pistons just diff rods and crank or vice...

What is the maximum size I can bore this engine out to? Is it possible to bore it to a 302? and If so how much would it cost? I would assume If I wanted to do that going on craigslist and buying a 302 with a T-5, or C-4 Transmission would be cheaper?

I just picked up a 1997 cobra that had a miss. I got the car for next to nothing so I wasnt to worried about it. It is either cylinder 5 or 1 but I ran a compression test and it only has about 10-15psi of pressure. Any ideas of what could cause this? Ive heard a couple things about a valve being...

so my motor is pushing 255rwhp and 295rwtq. the car is so dang heavy though!! my car weighs around 3200 pounds with me in it! so here are my options. find a diesel motor or a sick truck motor both with lots of power and torque. or find another v6 FROM another manufacturer (example this twin...

This is my first motor swap dealin with a modular motor so any help would be appreciated. Ok heres the deal, I bought a 2002 gt crate that comes with all the accessories including the computer. Im wondering what its gonna take to swap it into my 1998 gt. I didn't know if the 2002 motors use coil...

hey, ive got two quesions. one, how do i change the pistons that lift the top? two, one of my rear window motors is blown, and i tugged on the window to get it up, and the window came out. how do i get it back in? (any one that has a rear drive window motor for a good price p.m. me) thanks alot

I'm considering swaping my 289 out of my 1967 mustang, and puting in a 428, If it will fit. Does anyone know if there is even a possibility of a 428 fitting between my 1967 mustang shock towers.