Search Results for ‘oil’

Having major problems reinstalling my oil tube into the block. Came out, figured it should go back in. thought it might be pressed in, but still won't budge after the first 1/3 of a inch. Any help would be appreciated. Thanx.

hey guys ! hope all is ok.. have a question that im sure has been posted b4 but i need a little more in depth info* i just ordered my C&L racer intake and the sct x3 from bama and its getting to the time to change my oil in my 06 mustang 5 speed GT, i always put the full synthetic oil in my...

Hey guys: The other day I had the issue of not installing the oil pump shaft when putting the oil pump on. After about a week of thinking, I made up a long hard handle and then what I did was I welded a large nut onto the end of it, just so it would support the oil pump shaft clip, what the...

I went to install my oil pump driveshaft today. So i slide the shaft down the distributor hole until the little unbrella type guard hit the block, well realizing the oil pump driveshaft was almost to short and wouldnt go into the oil pump hole. It is a stock replacement oil pump. Do i need a...

i just got a 94 mustang gt and its getting time for me to change the oil. i think what is in it now is just conventional and i was wondering if i should just stick with it or switch. my friend tells me to stay with conventional because the seals are saturated with convintional and because...

every time i start my car up i get a huge puff of blueish smoke and then a constant stream of it. Can anyone help on telling me what it is and how can i fix it?

so about a month or so ago i changed the head gaskets on my 91 fox 5.0. I did everything as i was suppose to as i had a repair book by my side as well as a few knowledgable friends. the thing that i thought was wrong were the intake gaskets them self since i have a cobra intake on it but i...

so the other day i pulled up to a stop light and a cloud of smoke came from my exhaust... i limped it home and checked my oil it was a quart low but earlier that day it read full... i pulled my plugs and one was covered in oil... can anybody tell me if i fried a ring or something?

I have a 1993 LX 2.3 and my sons brought it home the other night with a nasty engine vibration. I pulled the dipstick and found it 3 quarts low. :happyhapp There are no visible leaks (I have even tried UV dye) no smoke, and no oil contamination in the coolant. Where has the Oil gone...

Im getting my gears installed and i need to know how much gear oil to get. I ordered the 1 quart bottle of royal purple max gear oil. will that be enough or do i need to order more its for a 2000 gt stock rear. Thanks

Hi, i have a V6 mustang from 1999. Everytime i turn on my car, before it warms up, it has a ticking noise from the engine. My dad told me the problem would be likely solved by using some kind of oil additive for a valve tap. my question is: what is the best kind of oil additive for a valve tap...

I just noticed a screeching sound while in motion, either just rolling or going 40mph. at rest the noise is not there but either in forward or reverse, the wheels screech. My oil is low and will be having it changed tomorrow but there is not a low oil light or check engine light on. In...

Hey guys.Im in need of some advice.I recently did my oil change as I always do,but this time the bolt was hard to loosen.When it did get loose,I heard a snap.I checked the bolt and it was fine.So I drain the oil and put the new filter.When I put the bolt back on to tighten,It wouldn't tighten by...

Hey there folks, I've got a couple hundred miles on my new Bullitt now, and thought it couldn't hurt to get the factory lubes and contaminants out, and get some fresh stuff in! I'm hearing a little rattling from either the trans or diff., and thought an oil change may help there. Does Ford put...

ok so its been a while since i posted on here, lemme fill ya in a lil first. im building a bullet proof 347<4 bolt splyed>, dart block eagle crank and rods je blower/nitrous 11cc dished pistons, f303 cam, trick flow 1.70 rollor rockers. world products windsor jr heads ported/polished/slighly...

Hey Everyone, Im new to this site and after reading through a number of posts I decided this should be the best route to keeping my 69 Mustang Tip Top. Basically Im having issues with my Gauges....I placed a New to me, but origional Harness in the car cause the one I bought the car with was...