Search Results for ‘pipes’

Hey guys, I picked up my 2011 Mustang GT 5.0 at the end of last summer. I'm about to pull the trigger on: 1) Kooks Long tube headers with catted H Pipes. (Question 1) -I've been reading that the X-Pipe gets better gains but it's negligible, and I want the deep muscle car sound rather than...

So I wanted to make my v6 sound louder, and I've heard of people cutting right before the muffler (muffler delete) and just putting a piece of straight pipe on or just curving it to point down. I was wondering if this is a good idea. I know it will not pass inspection, I know it will be...

I'm partially ahead of schedule on my mod on my mustang. I just wanted to know which would be better for a better acceleration and louder pipes. Would long or shorty headers be the way to go? I wanna go shorty but I heard the most sound comes from long tubes. Help!!

Hello! I am thinking about putting a x pipe off of cj ponys on my 66 coupe with the 289. Cj makes some for the stock manifolds. Does anyone have that one and if so is there clearance problems? If I can't get it to fit I'm just gonna run 2.5" pipes all the way back to a coupe 40 series flows with...

Im wanting to make my car sound louder without spending a lot of money, yet. I was talking to my father and he said the H-pipe adds more sound but im asking opinions. I wanting one that comes with cats, i cant afford to buy high flow cats for an offroad X or H-pipe as of now nor do i want to...

Quick Question, my exhaust from the header pipes is 2" dia. I have been given a 2 1/2" flowmaster exhaust set up. Can I just cut in a step up sleeve after the header and in front of the system? Going with out cats, just mufflers as I am beyond emissions. What happens with performance??? I feel I...

So i got to thinking, what if i get an x-pipe or h-pipe (which ever would be better and cheaper) im 18 in college with no job so im going on the cheap here, but i want a louder sound to my 99 v6 convertible, as well as mabe 5-10hp but my idea was to install the x or h pipe re using my stock...

I need 3 inch flowmaster tailpipes that will fit on a 1998 gt. The only ones that I found were these: FLOWMASTER TAILPIPES 3" WITH STAINLESS STEEL TIPS PAIR LX 1987-1993 | CJ Pony Parts The site says that they are for 1986- 1993 but i wanna know if they will fit. Will they? I mean they seem to...

I know there is probably a million threads about this, but I dont know to much about it. I have a 1992 mustang GT, stock H pipes and some type of Glass Pack exhaust. Its not very loud. It has some sort of a growl when you get on it, but theirs not much to the idle. Recently I got a stock H pipe...

i have a gt and i am putting an o/r h pipe on.. i have my own tunner and the car is tuned so when the check engine light comes on b/c there are no cats can i just do a custom tune to shut it off or do i need to buy the MIL Eliminators?

My mustang seems to enjoy surging to 2 grand when idling and will not "reset" to normal idling RPMs. I believe it may have had something to do with my passenger side headers breaking off of the rest of the exhaust just above the connection to the pipes. It was obvious shotty homemade exhaust...

i want to put exhaust cutouts on my new exhaust system. Is there anything i should be concerned about? What do you guys think about them?

i just got JBA shorty headers, kept the stock cats, cut the y-pipe off and replaced it with a x pipe, put in two 5" round borla mufflers, then have the pipes coming out right infront of my rear tires. now, i have three-ish inches of clearance. any advice to help raise the pipes?:happyhapp

Hi, i recently aqquired this 2007 Mustang v6, love it and have been wondering how to upgrade her. I am an old school Muscle guy, carbs, straight pipes, no cats, and bad gas mileage is my style. This is the first time i have ever owned a new car. I am looking at this gt take off exhaust i think...

Does anyone know where i can get stainless pipe thats pre bent to go over the rear axle on a 1997 gt? This is really aggravating me... I am trying to put a new 100 percent custom exhaust on and i cant find them anywhere ide love any help... thanks, zmds17

I have a 289 in my 68 mustang. Im going to put new exhaust on in sometime soon and was going to go with straight pipes with no mufflers. However i dont know if I want to go with 2 1/4 inch pipes or 2 1/2 inch pipes. What do you guys think?

Hi guys, I get my license in October and I really want to have duals on my 98 V6 by then. I am working at a supermarket and cannot and will not (most likely), be able to afford the $500 fee that my local exhaust shop quoted me. I have a neighbor that welds and i was wondering, would it be...

yo im from broomall pa and i have an 2004 its the v 6 im looking for the side skerts with the pipes and im also looking for a spoiler if any body knows were to go or if your selling eather of them please let me know

I've been looking into doing something new with my stock sixer exhaust for a long time but have never really figured it out. I was looking into doing tru dual exhaust, but i had questions. Would i have to just get the tru dual exhaust custom made? Also if i were to buy a new H-pipe, can i get...