Search Results for ‘rear axle’

Hello, I am new to this forum as a member. I own a 2008 V6 with the 5spd manual transmission. Eversince I owned the car the transmission feels like it was kind of loose whenever I would make a turn and try to shift. I have replaced the clutch and all the components a couple weeks ago and it did...

I have a 1978 Ford Mustang Cobra II with an 8.8 rear axle that is has a 2.79 gearing. The engine and transmission are both factory original 302 V8 attached to the C4 transmission. Can I use an axle off a 1996 Ford Ranger with an R6 8.8 Limited Slip that has a gearing of 3.73 on my 1978 Ford...

I just got this car and i’m trying to replace any old parts so just give me the bad news if there is any. I got a new suspension kit on the way. Main concern is what is that scraping my wheel? What looks wrong here?

So I had 4.10 gears installed on my car over a year ago and my car was lowered on Eibach sportline springs, bmr non-adjustable uca and bmr non-adjustable lca, so about 5 months ago I swapped out the springs with coilovers to go just a little lower and about a hundred miles or so after that I...

Hello everyone. I'm currently working on restoring my 00 Steeda GT after 21 years. I am finishing up the rear end assembly and need a little help from the 99-04 guys. I remember when my Steeda was new, it had a few paint stick markings (I believe on the axle tubes and maybe on the diff cover)...

Hey guys, doing a i6 to 302 swap in my 68 coupe. Im shopping for a rear end because I know the tiny little 7 and 1/4 inches would break, so I'm just looking for a list of bolt in or easily modified rear ends to use, preferably with disc breaks set up. I know the 95-98 explorer 8.8's are...

I have a 99 svt Cobra that I wrecked by sliding off a road and into a tree with. A few months after getting it all back to new it starts to make a grinding noise from the rear when turning left or when I hit bumps. After a mechanic had it for a couple days he couldn't find anything wrong. So...

2000 GT 4.6 question. We recently purchased this car. It appears the rear was changed and I am guessing by the 7mph the speedo is off, it probably now has 3.73 gears. ABS module was not communicating, and we sent it out to be fixed, which was a success. Trouble code stored in PCM for wrong...

Alright so after some days of research and dreaming of all my wishes of an engine I plan to build, I started to realize a lot goes with it other than just a swap. I plan on building up a 302 roller engine with high flow heads (probably like TW 170cc), a mild cam, and Edelbrock Performer RPM Air...

For what it's worth: While my 2011 V6 was up on the lift getting new tires, I noticed the axle vent on the passenger side was oozing axle oil all over. Unacceptable. After verifying that the axle was not over-filled with gear lube, and not being satisfied with any of the fixes I found on...

Hey guys i currently have an 88 lx all gutted in the middle of a 347 stroker swap. My question is will.a tko 600 trans fit without mods? And also what rear ends can i use like what vehicles can i take em from? Been searching but no luck. Thabks for your time

When I bought my car, I did a carfax on it. It showed that the car was in a wreck and that it has had previous rear end problems. When I bought my car, it had a small whine coming from the rear end and it has been getting worse. I took the rear end cover off and checked the inner bearings. They...

hi im new to the forum im in need of help I've been trying to decode my rear end for most of the day so if you guys can help i would greatly appreciate it. id tag S223B 2L3884B18 :?:

any ideas of what it could be? its pretty loud and annoying. just started the other day. Im thinking the axle bearing? Not sure tho, not any idea of what it could be. 1965 coupe.

This car slid and crashed into a curb really hard and broke a piece off the rim and popped the tire we changed the wheel/tire with a spare and the caliper was grinding down the rotor you could hear loud scraping but would be quieter at faster speeds what could be wrong with it. Bearings? Axle...

I have a 1987 GT that has a lean to the drivers side. The body shop found nothing on the frame machine. Wound up being the left front strut was 2" shorter than the other side. but after changing the struts out, the car still leans to the driver side. I know the front cradle has been shifted...

im trying to find out what size rear end my 1971 mustang grande has? it has 1 351 cleveland 2v engine with a fmx transmission

Whenever i am driving there is this squeaky noise which is coming from my rear. I went to my mechanic who says its my rear axle that is bent. I have custom 17'' pony rims on the car. I was wondering if I had to get a different type of rear axle than the stock because the rims are larger than the...