Ford Mustang Forum banner

swap

  1. Anyone have a parts diagram for a cable clutch bellhousing for a swap from a 88 TC?

    5.0L Tech
    Long story short im gonna be doing a 88 turbo coupe drivetrain swap soon. Its hydraulic in the turbo coupe but the fox body is going to be cable. Currently the fox body has no drivetrain but was a stick car so it has the pedals but thats it. I have a bare T5 cable bellhousing but thats all I...
  2. Swapping EPAS Module?

    2011 - 2014 Mustang GT Tech
    Hi Everyone, I have a 2011 Mustang 5.0 that was ordered new and delivered in Fall of 2010. It's probably part of the first batch off the line. As of right now, every suspension component in the car has swapped out with the exception of the front lower control arm. I know that the 2011 models...
  3. 347 swap touble

    Classic Tech
    I decided to go with the 347 stroker after everything i read here. I have one problem. The oil sump is larger on the new set up. It is also on the rear side of the motor. It doesn't fit with the steering linkage. I know we need more oil for this set up. What are my choices now? Can I simply...
  4. Can I use S550 exhaust cams in 11-14?

    2011 - 2014 Mustang GT Tech
    Hi all, I've got a new crate engine in my 2011 Coyote. It's got the 2015 cams/Phasers/chains etc. I've been told I need to change back to 11-14 VCT for the engine to run properly. I keep getting bank 1 and 2 intake cams over retarded codes. I've heard that the S550 exhaust cams can be used...
  5. SN95.0 PROJECT, Harness Help

    5.0L Tech
    Hey there, as you can tell I'm new to here. I wont bother you with telling you about me, lets get down to the nitty gritty. i have a 1992 BMW 325I sedan, i also have a 1995 SN95.0, with 32k original :) you see where im getting with this? good. Engine is installed Transmission installed Drive...
  6. Rear End Options

    Classic Tech
    Hello All, I have not posted on here in YEARS due to college but now that's behind me and I'm working on the mustang again. I had the recent displeasure of my engine dropping a valve and ruining the motor. I now have the whole drivetrain out and am working on what to do for my rear end. I...
  7. Engine Replacement

    2005-2010 Mustang GT Tech
    Last week I had some major engine issues. I dropped a valve into the cylinder and tore up my cylinder head and the block as well. Found a cheap low milage doner car on craigslist and I will be doing a swap soon. I have a 2005 Mustang 4.6 (5 speed) and will be swapping it to a 2006 Mustang 4.6 (5...
  8. Just bought an 89LX, now I have a tough decision

    5.0L Tech
    Hello Everyone, I'm new to this forum, but I've always read forums in the past. I just purchased an '89 LX 5.0 last Thursday. I bought it knowing I had to do some work to it, but had thought that it was a road ready project. That's not the case. I brought it to be inspected this week and the...
  9. Engine swap

    Classic Tech
    Hey guys! I currently have a 289 V8 in my 1966 mustang. I am looking at getting a bigger engine to put in. I was looking at a 302 or a 347. Does anyone know if I were to go with the 347 would I need to change anything in the engine bay such as motor mounts? I've read that with the 302 nothing...
  10. Rear end blew, any help would be much appreciated!

    V6 Tech
    I have a 1998 V6 Mustang and on the way to my new job the rear gears blew. I was thinking of swapping off my rear end from my 96, it has absolutely no play from the shaft to the wheels but it seems as though the 96 is squared off at the top mounts. Other than that I have found an 8.8 assembly I...
  11. 84 mustang engine swap question

    V6 Tech
    I have and 84 Mustang with a 3.8 V6 and auto transmission. I found a 96 mustang with a V6 and manual transmission. I was just wondering how hard it would to swap engines and transmissions. So what are the differences and steps or tips to do the job?
  12. 1994/1995 Mustang 4.6 4 Valve Swap

    5.0L Tech
    Hey all, in the future I plan on picking up a second 1994-1995 Mustang GT to accompany the current '95 GTS. I'll be swapping in a 4.6 DOHC I'm in the process of building (slowly...) and I've been doing as much research as possible before starting this and asking to see if anyone else has done...
  13. 1994 5.0 **swap** 1998 3.8 v6

    Introductions
    Hello, My name is Steve. I am amazed by how Lil information is out there on this swap. I have finished about %60 of the swap and have some concerns. 1st the totaled 94' I received as the doner car for around $800. Then after some talks with mechanics I decided to purchase my doner a 1998 white...
  14. Please Help! 1996 mustang gt cobra motor swap getting no crank

    4.6L Tech
    Hi Guys, I did a 1996 cobra 4v motor swap on my 1996 4.6l mustang gt i changed all the harnesses to the Cobra harnesses i also changed the PCM, fuse boxes, pats module,fuel pump,ccrm after doing the swap the car will not crank when attempting to start the car the pats light flashes and the low...
  15. 2000 V6 to v8 swap

    V6 Tech
    Hey guys, haven't posted on here in a bit. Wasn't sure how to post anywhere else but have a question or so. I have a 2000 v6, love the car, but am running into issues. I want to put money into it, but I don't at the same time because it's only a v6. So I was going to hold off. Now the CEL is on...
  16. help 3.8 swap to 3.8 superchrged from 90 tbird 94 mustang

    V6 Tech
    I knowits possible I know its been talked about before. I need to know where to start. and where you hook the vac lines from the supercharger. only swaps I have done were plug and play so I would like some advice and feedback.
  17. SN95 master clyinder on stock fox brake system

    5.0L Tech
    I know that you need the larger sn95 master cylinder in order to run rear disk. I eventually want to get rear end disk on my fox, but I don't have the funds for it right now. My current stock master cylinder is going bad and I need to replace it, so can I swap in the SN95 master cylinder now and...
  18. 4.6 to 5.4 (Possibilities/Read Multiple forums)

    4.6L Tech
    I was looking for someone that could possibly give me a little more insight into the possibilities of a 5.4 swap. I have a 00' GT Standard, my first Stang, with a gone motor(dreaded bearings) and for the time being I'm headed to the yards to find another 4.6 to drop in. But, I want to look into...
  19. swappable parts from crown vic police interceptor?

    4.6L Tech
    Hey guys, was poking my way through the salvage yard today and couldn't find what I needed from the mustangs there. However I did see lots of crown Vic police interceptors. I was wondering what parts you could swap from a police interceptor to a mustang, 95 v6 body. I have a 4.6l engine swapped...
  20. 98gt 4.6 or 302 build

    4.6L Tech
    so I have a 98 gt with a stock engine. I was looking to trade for a 94 cobra clone with a built 302, it I bored to 306, cams, intake, head work, and long tubes. Also looks ALOT better. is this worth a trade or even me adding some on top or is this a dumb deal?
Top