Ford Mustang Forum banner

trickflow

  1. Help Needed Adjusting the lifters on Trickflow top end kit

    5.0L Tech
    i have a 1988 mustang gt with a stock 302 block and a trick flow street burner top end kit. my question is in order to remove the valve covers to address some lifter noise, will i have to take off the upper intake to get the valve covers off or can i do a lifter adjustment without removing the...
  2. EGR issue with new Edelbrock Intake Manifold

    4.6L Tech
    Hey Guys, So the stang is away for the winter, and I bought a bunch of new parts to throw on during the time. One of them was the Edelbrock Victor Jr intake manifold, with a Trickflow 75mm tbody and plenum. It all bolted up fine, but it seems that my egr valve is now about 3 inches behind the...
  3. 1966 Mustang FB with 302: missing power or running right?

    Classic Tech
    Ok, fellow motor heads, I have a set-up and need to figure out if I'm getting the power I should be. I will share as many facts as I can think of.... -1966 Mustang Fastback. Appx 3100lbs -302 Hyd. roller block, stock 4" bore and 3.4 stroke. -TrickFlow 185cc twisted wedge heads, 58cc chamber...
  4. 66 mustang Am I on the right track? First hot rod

    Classic Tech
    Found a I6 66 coupe, had a frame of restoration done 5 years ago and new interior. (someones grandfather died and they acquired) :( motor and trans was never put back in. After hours of research, i decided not to rebuild the inline motor due to ridiculous price. So i decided to swap to...
  5. Aftermarket Cam Problems

    5.0L Tech
    I actually have a couple questions regarding a cam I have. I put a couple of mods on my mustang about a year back such as, TrickFlow upper and lower intakes, 70mm throttle body and a trickflow hydraulic camshaft. basically my car ran like crap, under powered, stalled constantly and I had a...
  6. Trick Flow top end install timing questions

    5.0L Tech
    Hey guys, I just finished my Trick Flow top end kit install. went with the 360hp/350tq kit with stage one cam. it runs great but i think it could be better. I was wondering if i should adjust my timing any with this kit and if so how much? Also dont know if it matters or not with timing but i...
  7. mustang 5.0 problems 1/4

    5.0L Talk
    i have a 91 mustang 5.0 my modds are trickflow intakes R-Series rpm range 2500 -7250 and stock e7 heads bbk headers msd 6a box h pipe flowmasters 75mm tb 255 fuel pump e303 cam and 355 gears t5 trany what should i be hiting at the 1/4 mile and are my intakes to much for my moddes
  8. cant pick a intake manifold for tricflow heads!

    5.0L Tech
    ok ready to ditch my gt40 setup once i sell the vortech v-1 s-trim (pm if interested) and heres what ill be gettin trickflow 170cc twisted wedges, TFS-51400002 custom cam 1.6 roller rockers 75mmtb and egr spacer new mass air meter with appropriate injectors (24#s???) already have all the little...
  9. Feedback Requested for my set-up

    5.0L Tech
    Hey everyone, Looking for some feedback, thoughts or improvements that can be made to my 93 LX Setup. With the latest tune I am at 287RWHP, and I want more. Although I don't drive much at all, this is my daily driver (we still have a family truckster) and street car. Ideally, I would like to...
  10. power estimate please (trickflow h/c/i)

    5.0L Tech
    *170cc trick flow twisted wedge heads with upgraded valve springs *trick flow track heat intake *custom cam or comp cam,maby keep the tfs1 i already have? *1.6 roller rockers *and all the little stuff like 75mm throttle body, mass air meter and fuel injectors, under drive pullies, ceramic...
  11. trading up from gt40 to trickflow heads

    5.0L Tech
    ok heres what i got now gt40p heads/cobra intake/tfs1 cam/65mm throttle body/and stock 1.6 rocker arms, and im wanting to trade up to trickflow heads like Trick Flow Specialties TFS-51400002 - Trick Flow® Twisted Wedge® 170 Cylinder Heads for Small Block Ford - Overview - SummitRacing.com or...
  12. What should the fuel pressure be on my 93 LX with minor mods?

    5.0L Tech
    Good afternoon everyone, looking for some help... I have a 93 LX, 5.0, F303 Cam, GT40 heads, Trickflow R upper/lower intake, 155lph fuel pump, 26lbs injectors, MSD ignition, 75MM TB, AC-Smog delete, recent tune, shorty headers with flowmasters, cold air intake etc... Looking to replace my fuel...
  13. 1999 Mustang GT - procharger fit with trick flow track heat manifold?

    4.6L Tech
    i just bought trick flows track heat manifold on my 1999 2v GT. one of the fitment requirements is to turn the alternator 180deg to where the pulley is facing the engine and the alternator is almost resting on the radiator. i want to put a procharger on my car but from the pictures i have seen...
  14. 1993 Mustang 5.0 Foxbody Budget Build

    5.0L Tech
    Hey everyone, thanks for looking and helping. I have just finished a budget build for my 93 Mustang LX. I replaced the completely stock (with bolt ons) with a 93 GT engine, therefore leaving me with the following: GT40 Heads, 1.6 Roller Rockers, F303 Cam, BBK Shorty, BBK Cold Air Intake...
  15. 1994 Mustang GT, SCT 4 bank eliminator chip questions?

    5.0L Tech
    I have a 1994 mustang gt and I'm wanting to put gt40 heads and intake also a trick flow stage 1 cam but don't want to spend the money on a tune cause I know it's not gonna run good with out one that's why I was gonna see if I could just get a custom tune for that set up on the 4 bank eliminator...
  16. 5.0 wants to die after trickflow cam(please help)

    5.0L Tech
    just installed a trickflow stage 1 cam and it sound great and good power but when i start the car WARMED UP it wants to die and rpm dives to 500, i got to tap the gas for the first 30 sec or so then it surges from 1000 to 1500 and slowly goes down to 950(idle screw on t/b wont let me go lower)...
  17. about to order a cam today of tomarrow

    5.0L Talk
    really close to ordering a cam today maby tomorrow i was set on a tfs1 but then i herd the stage 2 YouTube - TFS 2 Cam w/ Hooker Longtubes and Dynomax Mufflers i really like the sound of the stage 2 but im thinking it will hurt me more than help with my gt40 set up so should i just get the...
  18. do i need new valve springs

    5.0L Tech
    do i need new valve springs because i bought gt40p heads (off a explorer) and i want to use ford racing 1.7 roller rocker arms? in 3 months or so i want a tfs1 camshaft but i thought i would upgrade to Trick Flow Specialties TFS-2500100 - Trick Flow® Valve Spring Upgrade Kits - Overview -...
  19. intake maniflold

    5.0L Tech
    so i got to wait on heads cam and intake due to money would getin a trick flow track heat intake with a 75mm throttlebody and bigger maf be pointless with my stock heads how much of a hp increase with my mods (in signature) oh and do you feel the difference any good deals or comments...
  20. Trickflow 360 hp track heat top end kit

    5.0L Tech
    Im about to buy this kit from trick flow http://www.trickflow.com/partdetail.asp?part=TFS-K514-360350B&view=1&N=400098+150+ i want to know what you think about this kit and what should i clean or replace while im down there and also i was going to buy the (absolute) biggest throttle body...
Top