Ford Mustang Forum banner
Status
Not open for further replies.
1 - 10 of 10 Posts

·
Registered
Joined
·
3 Posts
Discussion Starter · #1 ·
I just found this site and love it. I have some questions about my V6 and would like some help if possible. I am trying to get the seat belt beep to go away. I understand I need to wear my seat belt, and I do but this thing beeps all the time non stop even if I am just sitting in my car with it in park. Please help if you can. Thank you:headscratch:
 

·
Registered
Joined
·
25,075 Posts
:hello: and :welcome: Enjoy the site!! :happydancer:
Do post some pictures into your gallery soon!!

When your not using it? Simple plug it in lol Just kidding. I am a seatbelt fan after working as a firefighter/emt lol.

Check out the 2005+ forums!!
 

·
Super Moderator
Joined
·
40,152 Posts
welcome to the site,enjoy!!!!
 

·
Registered
Joined
·
1,203 Posts
Welcome David!

:youwelcome:
 

·
Premium Member
1965 Mustang coupe
Joined
·
72,878 Posts
Welcome...

BELT MINDER DEACTIVATING/ACTIVATING

Preparation
1. Before deactivating/activating the belt minder, set the parking brake.
2. Place the gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission).
3. Place the ignition switch in the OFF position.
4. Close all the vehicle doors.
5. Unbuckle the driver and passenger safety belt.
6. Place the parklamps/headlamps switch in the OFF position.
Deactivating/Activating

NOTE:
• Steps 1-7 using only the driver safety belt will permanently enable/disable the beltminder feature.
• Steps 1-7 using only the passenger safety belt will permanently enable/disable the beltminder feature.
• Only one side (driver or passenger) can be enabled/disabled per ignition switch cycle. While programming the driver side, any activity on the passenger side will terminate the programming sequence. While programming the passenger side, any activity on the driver side will terminate the programming sequence.
• The programming sequence will terminate if a system fault occurs that requires the illumination of the safety belt, or airbag warning indicator at any time during the programming or confirmation.

1. Turn the ignition switch to the RUN position. (Do not start the engine.)
2. Wait until the safety belt warning indicator turns off. (approximately 1 minute )
3. NOTE: Step 4 must be completed within 60 seconds . Buckle and unbuckle the driver or passenger safety belt 9 times, ending with the safety belt unbuckled. The air bag warning indicator illuminates for 3 seconds after this step.
4. After the air bag warning indicator turns off, buckle and unbuckle the safety belt again. This enables the belt minder if disabled or disables the belt minder if enabled.
5. Confirmation of the beltminder being enabled is by the airbag warning indicator flashing 4 times per second for 3 seconds , followed by 3 seconds again.
6. Confirmation of the beltminder being disabled is by the airbag warning indicator flashing 4 times per second for 3 seconds .
7. After confirmation, the deactivation/activation procedure is complete.
 

·
Registered
Joined
·
2,961 Posts
Welcome to AFM... Glad you joined us!!
 

·
Registered
Joined
·
46,010 Posts
Hiya, welcome to the site. That info the Colonel gave you should help.
 

·
Registered
Joined
·
10,019 Posts
:hello:AND:welcomeflowers:TO THE SITE.
Probably the best Mustang site on the web.
Get advice in a Tech' Section or just chew the fat in the Lounge. ENJOY!
 

·
Registered
Joined
·
41,825 Posts
Hi there and welcome to the site.
 
1 - 10 of 10 Posts
Status
Not open for further replies.
Top