Ford Mustang Forum banner
1 - 20 of 22 Posts

·
Registered
Joined
·
287 Posts
Discussion Starter · #1 ·
The last forum I participated in had a thread called "What have to done to your car today?" People talked about just what the title implies. Everything from a good wax job to major mods. It was an ongoing thread and, by the time I joined that forum, it was several years old and covered dozens of pages. I see a lot of threads here that could fall under that general heading. I think the Mustang forum should have something like that.
Anyone else?
 

·
Registered
Joined
·
245 Posts
Technically, nothing today. Last week, I installed Steeda Charge Motion Delete Plates and a Ford Racing GT500 Throttle Body. I did some 2010 OE Style Black Wheels 3 weeks ago. Now I am just waiting to install an SLP Line Lock Kit and put my Nitto 305/40 R18 on the car and light'em up.
 

Attachments

·
Registered
Joined
·
287 Posts
Discussion Starter · #7 ·
Tuesday I installed a set of factory -style alloy pedals plus a matching dead pedal I got on sale from LMR. The gas and brake pedals were pretty easy. Because the reviews said the 3M tape on the gas pedal was a bit weak I also used epoxy. The dead pedal was a bit more involved. Had to pull the door sill trim, then the kick panel as well as pull up the carpet so I could access a 13 mm bolt to mount the d/p to.
Anyway, it looks great and the d/p makes it more comfortable as well.
 

·
Registered
Joined
·
3,171 Posts
Gonna grease the LCAs tomorrow.
Also mash the gas pedal at least once or twice a day.
 

·
Registered
Joined
·
1,325 Posts
Mine is just sitting in the garage...BUUUT I have these waiting to go in!
 

Attachments

·
Registered
Joined
·
1,153 Posts
Snow mostly gone here now and streets are mostly dry, so got the stang out last night for first test drive after installing an Exedy Mach 500 clutch, flywheel and SR Performance Braided Stainless Clutch Line.

All went really well. Clutch was quiet, very precise and buttery smooth, . Going to drive the prescribed 500 miles though before hitting it real hard .
 

·
Registered
Joined
·
476 Posts
A nice hand wash... It's the car equivalent to a back massage.:wink:
 

·
Registered
Joined
·
385 Posts
Installed new napa chassis parts ball joint $100. Each guaranteed for life to replace those that where on my new frpp LCA that I bought last year that only lasted 15K km.
 

Attachments

·
Registered
Joined
·
2,388 Posts
this week mon/tue drove her to work wed she has been sleeping in the driveway due to the snow storm we had here

Hopfuly I'll get to drive her and clean her up next week (IF it doesn't snow here again)
 

·
Banned
Joined
·
1,359 Posts
drove the stang to work only to have a 5.0 want to run, she held for a few but the 5.0 pulled away (I had to turn). add supercharger, forged rods and pistons to build list. GDI! it never ends but it sure as hell is fun.
 

·
Administrator
Joined
·
13,242 Posts
This thread is a good idea. A lot of car/truck/bike sites have similar threads. I`ll insert just one word in the thread title if the OP does not mind, & that word is "with". That will encompass pretty much every interaction you could have with your car. I`ll also make it a sticky.
 

·
Registered
Joined
·
174 Posts
Well, it was technically early Monday morning, but I was mocking up the carb and air cleaner on this to make sure the air cleaner cleared the valve cover

 
  • Like
Reactions: Stustu07

·
Registered
Joined
·
4,601 Posts
Nice engine. Going to look good in the car. Only thing I have done lately is started the car over the weekend. First time in a few months. Been busy and wife has the Jeep now. Maurice
 

·
Registered
Joined
·
209 Posts
Well, I have leaned against it while taking the kids (dogs) outside.
About all I have done lately. New job and I am just getting used to working again, so hoping to get back to working on it soon.
Russ
 
1 - 20 of 22 Posts
Top